Panasonic TH-50PH12L Connections, For TH-42PH12U, TH-50PH12U, AC cord fixing, Cable fixing band

Page 8

Connections

For TH-42PH12U, TH-50PH12U

When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation.

Speakers (Optional accessories)

Speaker terminal (R)

Speaker terminal (L)

AC cord connection (see page 14)

– AC cord fixing

1

 

2

1

 

 

2

1

2

Note:

Make sure that the AC cord is locked on both the left and right sides.

1Plug the AC cord into the display unit. Plug the AC cord until it clicks.

2Fix the AC cord with the clamper which is attached to the unit.

Close

Push until the hook clicks.

Open

2. Pull off.

1.Keep the knob pressed.

Unplug the AC cord

Unplug the AC cord pressing the two knobs.

Note:

When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet first.

Cable fixing band

Secure any excess cables with band as required.

Note:

One fixing band is supplied with this unit. In case of securing cables at two positions, please purchase it separately.

Pass the attached cable fixing band through the clip as shown in the figure.

To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure.

While ensuring there is sufficient slack in cables to minimize stress (especially in the power cord), firmly bind all cables with the supplied fixing band.

To tighten:

To loosen:

 

Push the catch

 

Pull

 

 

 

 

 

1

2

 

 

 

 

Pull

 

R AUDIO

L

PR/CR/R PB/CB/B

Y/G

 

AUDIO

 

COMPONENT/RGB IN

 

 

 

 

SLOT1

SLOT2

 

SLOT3

PC

IN

SERIAL

Optional Terminal

 

Dual HDMI Terminals

 

COMPONENT/RGB IN andAudio

Board Insert Slot

 

(equivalent of Dual HDMI

 

IN Terminals (equivalent of BNC

(covered)

 

Terminal Board (TY-

 

Component Video Terminal Board

 

 

FB10HMD)) (see page 12)

 

(TY-42TM6A)) (see page 13)

Note: At factory shipment, Terminal boards are installed in SLOT 2 and SLOT 3.

From EXTERNAL

 

From SERIAL

monitor terminal

 

Terminal on

on Computer

 

Computer

(see page 10)

 

(see page 11)

8

Image 8
Contents Operating Instructions Manual de instrucciones English EspañolRisk of Electric Shock Do not Open Important Safety Instructions FCC Statement Trademark CreditsSafety Precautions When using the Plasma DisplayMaintenance Safety Precautions / MaintenanceSetup AC Power Supply CordRemote Control Batteries AccessoriesAccessories Supplied Connections For TH-42PH12U, TH-50PH12UAC cord fixing Cable fixing bandConnections For TH-42PH12L, TH-50PH12LSignal Names for Mini D-sub 15P Connector PC Input Terminals connectionSignal names for D-sub 9P connector CommandSerial Terminals connection Communication parametersHdmi connection for TH-42PH12U, TH-50PH12U AV connection for TH-42PH12L, TH-50PH12LVideo VCR CamcorderComponent / RGB connection RCA-BNCDVD DTV-STBConnecting the plug to the Wall Outlet Power on / OFFConnecting the AC cord plug to the Plasma Display OSD Language Present Time Setup Display Orientation Power on / OFFWhen first switching on the unit Selecting the input signal INPUT1 INPUT2A INPUT2B INPUT3 PCRemote control sensor Volume Adjustment Main Power On / Off Switch Power IndicatorInput button Input signal selection Basic ControlsBasic Controls On-Screen Menu Displays Power Consumption SpecificationsSpecifications NTSC, PAL, PAL60, SECAM, Modified NtscPanasonic Professional Flat Panel Display Limited Warranty For the U.S.A and Puerto RicoLimited Warranty Statement For CanadaPage Page Customer’s Record Panasonic Professional Display CompanyExecutive Office Panasonic Canada Inc