Panasonic TH-37PWD5UZ operating instructions Safety Precautions, Set up, AC Power Supply Cord

Page 6

Safety Precautions

WARNING

Set up

Do not place the Plasma Display on sloped or unstable surfaces.

The Plasma Display may fall off or tip over.

Do not place any objects on top of the Plasma Display.

If water spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result in fire or electric shock. If any foreign objects get inside the Plasma Display, please consult an Authorized Service Center.

Do not cover the ventilation holes.

Doing so may cause the Plasma Display to overheat, which can cause fire or damage to the Plasma Display.

If using the pedestal (optional accessory), leave a space of 3 15/16” (10 cm) or more at the top, left and right, 2 3/8” (6 cm) or more at the bottom, and 2 3/4” (7 cm) or more at the rear. If using some other setting-up method, leave a space of 3 15/16” (10 cm) or more at the top, bottom, left and right, and 3/4” (1.9 cm) or more at the rear.

Avoid installing this product near electronic equipment that easily receives electromagnetic waves.

It may cause interference in image, sound, etc. In particular, keep video equipment away from this product.

AC Power Supply Cord

The Plasma Display is designed to operate on 120 V AC, 50/60 Hz.

Securely insert the power cord plug as far as it will go.

If the plug is not fully inserted, heat may be generated which could cause fire. If the plug is damaged or the wall socket plate is loose, they should not be used.

Do not handle the power cord plug with wet hands.

Doing so may cause electric shocks.

Do not do anything that might damage the power cable. When disconnecting the power cable, hold the plug, not the cable.

Do not make any modifications, place heavy objects on, place near hot objects, heat, bend, twist or forcefully pull the power cable. Doing so may cause damage to the power cable which can cause fire or electric shock. If damage to the cable is suspected, have it repaired at an Authorized Service Center.

If the Plasma Display will not be used for a long period of time, unplug the power cord from the wall outlet.

If problems occur during use

If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odor is detected from the Plasma Display, unplug the power cord immediately.

Continuous use of the Display under these conditions might cause fire or permanent damage to the unit. Have the Display evaluated at an Authorized Service Center. Services to the Display by any unauthorized personnel are strongly discouraged due to its high voltage dangerous nature.

If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet becomes damaged, disconnect the power cord plug immediately.

A short may occur, which could cause fire. Contact an Authorized Service Center for any repairs that need to be made.

6

Image 6
Contents For assistance, please call 1-888-VIEW-PTV843-9788 Operating Instructions TH-37PW5Progressive Wide Plasma Display For assistance, please callRisk of Electric Shock Do not Open Important Safety Instructions Table of Contents Canadian Notice FCC CautionAttach the ferrite core Trademark CreditsAC Power Supply Cord Safety PrecautionsSet up If problems occur during useWhen using the Plasma Display Cleaning and maintenanceSafety Precautions TY-SP42PWD3W, TY-SP42P5W-K TH-42PW5Optional Accessories AccessoriesAccessories Supplied Check that you have the Accessories and items shownObserve the following precautions Remote Control BatteriesPrecaution on battery use Helpful HintBasic Controls Video S VideoVideos VIDEO, Component Connections SpeakerCable fixing bands Connections Speakers connectionAV Input Terminals connection An S Video VCR connection⋅ RCA audio video cables connection Component signals Y, PB, PR connectionCOMPONENT/RGB Input connection AUDIO-VIDEORGB signal R, G, B, HD, VD connection BNC-RCAInstalling the ferrite core Small size Installing the ferrite core Large sizePC Input Terminals connection AV VIDEO, S Video input COMPONENT/RGB input PC RGB input Signal Names for D-sub 15P ConnectorVIDEO/COMPONENT/RGB/PC input signals COMPONENT/RGB/PC inputCommand Basic format for control data Serial Terminals connectionCommunication parameters Connecting the plug to the Wall Outlet Power ON/OFF and Input Signal SelectionPower ON/OFF AC cord connectionSelect the Input Signal Power ON/OFF and Input Signal SelectionSelecting the On-Screen Menu Language On-Screen Menu Display from Remote Control To Picture adjust menu seeOn-Screen Menu Display from Remote Control Aspect Controls Normal Zoom FullAspect Controls Adjusting Picture POSITION/SIZE Adjusting screenSIZE/CLOCK Phase Helpful Hint N / Normalize Normalization Adjusting Picture POS./SIZESize Clock Phase POSTreble Sound AdjustmentBass BalanceSurround Controls Surround Surround ButtonDynamic Picture AdjustmentsStandard CinemaColor Picture AdjustmentsPicture TintOn / OFF selection Screensaver For preventing after-imagesNegative / Scroll selection White BAR Scroll NegativeSide BAR Adjust OFF, DARK, MID, Bright OFF Dark MID BrightSET UP for Input Signals 3D Y/C Filter For Ntsc Video imagesSelect If the image becomes unstable SET UP for Input SignalsColor System / Panasonic Auto Auto PAL Secam NtscFreq kHz/V-FREQ Hz Setting RGB sync signalSetting PC sync signal Displays the H Horizontal/V Vertical frequenciesTroubleshooting Plasma Display panel Symptoms CheckPage Page Specifications Specifications Customer’s Record Electric Corporation of America Puerto Rico Inc. PSC