Panasonic PT 56DLX25 Using the CH/VOL Button, Channel and Program Tuning, Unit Status display

Page 33

Using the CH/VOL Button

„Select desired channel:

Press CH <> or NUMBER keys.

„Adjust to desired volume level:

Press VOL + or VOL -.

Notes:

•The channel number and volume level are stored even after the unit is turned off.

•Power consumption can be reduced if the volume level is lowered.

3

1

2

3

4

5

6

 

 

7

8

9

 

 

0

 

4CH

VOL OK VOL

CH

Direct Tuning Example

Step

Action

Channel Banner

Display

 

 

1

Press 1

1

2

Press 5

15

3

Press -

15-

4

Press 1

15-1

5

Press OK

15-1

Channel and Program Tuning

Channel and Program tuning in digital television differs from conventional television. With DTV, many programs can exist within a single 6 MHz channel. These channels behave as sub-channels within a single channel. When tuning to a digital channel, the unit will also tune to a program and will indicate the channel and program in the on-screen Channel Banner display.

In order to select channels properly, Auto program must be performed (P. 29).

Follow the procedure below to directly enter the channel number using the NUMBER keys on the Remote Control.

Select analog channel

Note:

•If, during channel selection, no action is taken for several seconds, the Channel Banner is exited and the currently input channel is automatically selected.

Unit Status display

Press the Channel<>or RECALL button, except when

the MENU screen is displayed, to display current unit

status information.

Channel Banner: Minimized

 

Press CH<>to minimize the displayed

CH

channel banner. It will display the

 

VOL OK VOL

channel number, and the station

CH

identification (if available).

 

Basic Operation

1

2

1 2 3

4

5

6

7 8 9

0

CH

VOL OK VOL

CH

Press the NUMBER keys on the Remote Control to enter the Channel number. Press OK.

The following is an example of tuning to channel 15.

Direct Tuning Example

Step

Action

Channel Banner

Display

 

 

1

Press 1

1

2

Press 5

15

3

Press OK

15

Channel Number

15-2

ABC - HD

Station identifier

Note:

•The Station identifier is not displayed when you use Split Screen mode.

Note:

•If, during channel selection, no action is taken for several seconds, the Channel Banner is exited and the currently input channel is automatically selected.

Select digital channel

1

1

2

3

If tuning a digital channel and your

4

5

6

channel contains more than one

 

7

8

9

program, press PROG and enter

0the program (1, 2, 3 etc.) using the NUMBER keys. Press OK. The

2

PROG

following is an example of tuning to

 

channel 15-1.

 

 

Channel Banner: Maximized

 

 

 

 

 

 

 

 

 

 

 

 

 

Press RECALL to maximize the

 

 

 

 

 

 

 

 

displayed channel banner.

 

Channel, Program and Station identifier

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Program title

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

15-2

 

 

 

 

 

Andrew’s

cooking show

 

 

 

 

 

 

ABC - HD

 

CC

SAP

TV-G

1080i

STANDARD

4 : 3

 

 

 

30

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Closed Caption

 

Rating

 

 

 

Picture mode

Time remaining

 

 

 

 

 

 

 

 

 

 

 

 

setting

 

in Sleep Timer

 

 

 

 

resolution

 

 

 

 

 

SAP indication

Signal

Aspect

 

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents
Three Important Reasons to Register Your Product For assistance, please call Immediately View PTV843-9788For assistance, please call Follow all instructions carefully Keep these instructions for future referenceTrademarks Getting StartedFCC Caution For assistance, please call 1-888-VIEW PTV843-9788Declaration of Conformity Models NumberTable of Contents Before Using Emergency Alert System EAS Forced Tuning Remote Control Battery InstallationReset All Memory Functions Observe the following precautionsGlossary and Acronyms Location of Controls Illuminated Remote ControlVOL -+ / ŻŹ NumberFront View Model PT-56DLX75 unit shown Controls and Terminals on the Projection DisplayConnector Audio Out Output audio signal Output audio signalRear View Model PT-56DLX75 unit shown VentConnecting the Antenna / Cable to the RF in Terminal InstallationAntenna Connection VHF AntennaCable Connection From cable CableCARDTM CableCARD ConnectionHow to connect the 1, 2, 3 Input Terminals Input 3 is located on the front of the unit. PConnects VCRs and other peripheral equipment S-VHS VCR Connecting a DVD Player to Component Video How to connect the Component Video Input TerminalsComponent Signals Y, PB, PR that can be Input DVD PlayerRecording Equipment S-VHS /VHS VCR How to connect the AV OUT TerminalsAudio Adjustments How to connect the AmplifierAnalog Audio Out Stereo System Stereo Amplifier and SpeakersFirmly connect the cable to the connector ProcedureDigital Audio Out Amplifier with built in Dolby Digital decodersConnecting a PC to PC How to connect the PC in TerminalsPC in Terminal D-SUB 15P Pin Layouts NC Not connectedKHz Personal Computer Signals RGB signals that can be inputConnection diagram How to connect the Hdmi input terminalWhen audio signal input is digital When audio signal input is analogProcedure Audio signal PCMCompatible formats Turning the Power on and OFF Power on / OFFPower on Power OFFFor your convenience, First Time Set up menu will First Time SetupLanguage Auto programExample of a procedure Basic Menu NavigationButton operation during Menu display Menu navigation Basic Operation Other Adjust sub-menuSwitching languages for display Tuning channelsPress to select Setup icon Press to display the Setup menu Press Menu to display the Main Menu screen Press to select Program Automatic program setting Channel Channel menu„ Edit Caption When a preset Caption has been entered Manual program settingWhen selecting a desired Caption manually Press to display the Setup„ Edit Add „ Preview CH„ Edit Favorite Rapid Tuning Selecting Input Mode„ Card input mode Photo Viewer is selected Projection Display operationUsing the CH/VOL Button Channel and Program TuningUnit Status display Use Favorite Feature Favorite FeatureSet Favorite Feature Audio MuteSleep Timer Feature Select Audio Mode for TV ViewingDigital mode Analog modeAspect mode is changed each time when Aspect is pressed Changing the aspect modeMode Picture Explanation Aspect ControlsSplit screen „ Caution when HDMI/PC is inputSplitting the screen Changing the channelTV/VIDEO Press to select the desired input Mode Select desired input mode Right screenSwapping left and right screens Press to swapPicture Menu is inaccessible when no signal is present Picture AdjustmentsPress to adjust each item Press to select PicturePC Adjust Picture ModePress to select picture mode Press to display the PC Adjust MenuAdvanced Adjust Other AdjustAdjust menu Press to display the Advanced Adjust menuAudio Mode Audio AdjustmentsNormal / Bass / Treble / Balance Press to select AudioPress to select BBE setting Other detailed audio adjustments can be madeCH Press to select BBE Set Sleep Timer Sleep Timer FeaturePress to display Timer menu Sleep time may be set using the Sleep button. P„ Create Secret Code First Time Setting Lock FeatureEnter Secret Code „ Enter Secret CodeLock Set Rating level settingBlock program Channel Lock Block channel selectionMonitor out setting Age Blocked Description Based Content Group RatingsPress to select Monitor out Press to select On or Off Change password Enter a 4-digit passwordBlocking Messages Insert/Remove the Card Photo ViewerInsert the Card Remove the CardCard icon Jpeg thumbnailPress to display the Photo Viewer SD button may also be pressed for Photo Viewer mode. PExit Photo Viewer Card Warning MessagesIndex Area Operation Press SD to exit Photo ViewerSingle Play Mode Exit Slide Show mode Slide Show ModePress during Single Play Mode Press to select each item Press to set each itemSignal meter Setup FeaturesPress to select Signal meter Press to display signal meterCC Mode for Analog CC ModeInput labels CC Closed CaptionDigital settings CC Mode for DigitalCC Reset SettingsOther adjust Setup ResetAbout Programming Without a Code Programming the RemoteOK to store the code VCR Infrared Codes IndexComponent Codes Brand CodeCable Converter BOX DVD, CD Players Infrared Codes Index Remote Control Quick Reference GuideCodes For CD Player AMPLIFIERS, and DBS Infrared Codes IndexOperating a VCR Operating Components with Remote ControlOperating a Cable BOX Operating a DBSProgram the Remote Control to operate audio receiver Program the Remote Control to use with DVDOperating a DVD Operating a ReceiverOperating a PVR Personal Video Recorder Program the Remote Control to use with a PVRIndicator Indicator Symptom Problem Possible SolutionLamp unit replacement period Lamp replacement procedurePower button Lamp indicator Power indicator Replacing the lamp unitInsert the new Lamp Unit being careful Insertion direction Close the Lamp Cover Turn the Lock/Open Knob to the rightReplace the Front cover OFF TroubleshootingPT-56DLX75 PT-61DLX75 PT-56DLX25 SpecificationsCustomer Services Directory CleaningLimited Warranty Coverage Limited WarrantyCarry-in or In-Home Service Limited Warranty Limits And ExclusionsPreamble Other InformationAbove provided that you also do one of the following END of Terms and Conditions How to Apply These Terms to Your New ProgramsVersion 2.1, February Other Information Information USA How to Apply These Terms to Your New LibrariesCableCARD IndexModel Number Serial Number Customer’ Record
Top Page Image Contents