Panasonic PT 52DL10 operating instructions Power on / OFF

Page 20

Power ON / OFF

Connecting the Plug to the Wall Outlet

Turning the Power ON and OFF

Always be sure to follow the procedure given below to turn the projection TV power ON and OFF.

•The lamp cooling fan will continue to operate for approximately 90 seconds after the power is turned off by the remote control. At the same time, the power indicator will blink Orange.

Normally, use the remote control to turn the power OFF (turning the picture OFF).

Do not disconnect the power cord from the power outlet or do not open any circuit breakers while the cooling fan is still operating.

Do not disconnect the power cord from the power outlet while in Stand-by mode.

•When you want to turn on the power again immediately after turning off the power during the operation of the projection TV, be sure to wait until the cooling fan stops and then turn on the power.

Setting the projection TV to Stand-by, the power indicator will light up red.

POWER

R-STANDBY LAMP TEMP G-POWER ON

POWER

R-STANDBY LAMP TEMP G-POWER ON

Push the Power switch on the projection TV to turn the power on.

The Power Indicator will become Green and blink (approximately 10 seconds).

CH123

STEREO

SAP

MONO

NORMAL

Example: The screen above is display for a while after the projection TV is turned on. (Setting condition is an example.)

Push the Power switch on the projection TV to turn the set off. The Power Indicator will no-illumination.

The Power Indicator will light

•Power-OFF ............ Not illuminate

•Stand-by ................ Red

•Power-ON .............. Green

Note:

When the power is switched off using the POWER switch on the set, the internal cooling fan also stops operating. Therefore, the lamp is not sufficiently cooled and will take a while for it to turn ON again.

20

Image 20

Contents For assistance, please call 1-888-VIEW PTV843-9788 For assistance, please callOr send e-mail to consumerproducts@panasonic.com Puerto RicoImportant Safety Instructions Important Safety Instructions For Projection TVImportant Safety Instructions Dear Panasonic Customer TrademarksTable of Contents Installation AC Power Supply Cord Safety PrecautionReceiver Location Optional External EquipmentRemote Control Battery Installation InstallationPrecaution on battery use Observe the following precautionsConnecting the Antenna Cable to the RF In Terminal Antenna / Cable ConnectionIncoming Cable From Home Antenna 75 Ω Incoming 75 Ω Cable From Cable CompanyAntenna Connection Cable Box, no VCR Output InputAntenna Connection Cable Box, and VCR Antenna Terminals On the Back Projection TVHow to connect the 1, 2, 3, 4 Input Terminals Connects VCRs and other peripheral equipmentVideo Audio VHS VCRHow to connect the Component Video Input Terminals How to connect the AV Prog. Out Terminals Video CableHow to connect the PC Input Terminals Signal Names for D-SUB 15P ConnectorVertical scanning Analog RGB signals that can be inputDisplay mode name No. of dots H ⋅ Illuminated Remote Control Location of ControlsLocation of Controls Controls and Terminals on the projection TV LampTemp PC Input terminalComponent signal input RearPower on / OFF Power on / OFF Power on / OFF buttonPower Indicator Remote Control SensorFlow Chart of Main menu Select Menu desired by pushing RightButton or Left Right Button on Main body can also beFlow Chart of Main menu To Channel To Sleep Timer To Audio ModeTo Picture To Position To Audio To Clock SizeTuning channels Automatic channel programming O G R a MChannels ModePress to select YES N U a L Program Tuning channels Manual channel programmingSelecting the Program Channels menu Adding or deleting channels Aspect mode changes each time the Aspect button is pressed Aspect ControlsNormaljust Fullzoom Full NormalAspect Controls SizePress to select the desired volume level VHF, UHF and CatvPress to turn the projection TV on Press to operate the projection TV withPress while pointing the remote control Cable TVConfirming Towards the cable TV tunerChannel search When a channel button is pressed during channel searchSearching for the desired channel Channel search Turning the power on and switching input modes Playing a VCR or other peripheral equipmentConfirming connections VCRFactory default setting Playing games in game modeTurning on the projection TV and switching to game modes Mute Recall / MuteRecall On-screen display Selecting the screen mode for split screen Split screenSplitting the screen Freezing picturesScreen mode names Split screenChanging the channel of the right screen Swapping left and right screensPOSITION/SIZE Adjusting screen position and sizeAdjusting screen Adjusting screen position and size Switching screen widthChanging vertical size Displaying images cut off from the screenAudio Adjustments Normalize NormalAudio Adjustments Turning the speaker sound on and OFFSpeakers OFF Speakers onPicture Adjustments DynamicPicture Adjustments VOL Action Selecting Video menu Switching to Scan ModePlaying special video software CC on Mute C1 CC Mode OFF Closed CaptionsPress to select Closed Caption Press to display the Closed Caption screenOFF C1 C2 T1 T2 T4 T3 C4 C3 Press to select CC Mode Press to select from the followingClosed Captions Lock Feature Access grantedLock Input codeLock Feature Rating turns red when onSetting the Motion Picture Rating screen View NR PROGRAMS?Locking and unlocking Setting the TV Parental Programs screenSetting Customizing the Video Input labels Press to display the Video Input Label screenCustomizing the Video Input labels Video VCR Game Blank HD VCR DTV DVDAudio Mode is valid only during TV mode Selecting Stereo / SAP / MonoUsing the off-timer 30 60 90 minutes to select times Press to exit menuVideo game player to Video Input Press to select DVC Playback Mode Normal When playing normal imagesFrame When displaying Frame Recording modeTurning OFF digital comb filter 3D Y/C Filter OFFAutomatically changing screen size for Video Input modes Sdtv Hdtv Clock is valid only during PC mode Adjusting the clockClock Phase 0 Clock PhaseSwitching languages for display Press to select LanguagePress to display the Language screen Press to select preferred languageLamp unit replacement period Replacing the lamp unitImportant Points to keep in mind Lamp unit Part No. TY-LA2000When code known CBLDBS RcvrInfrared Remote Codes for Specific Components Operating peripheral equipment using the remote controlWhen code not known Maker Set Up No VCR Infrared Codes IndexMaker CablePlayer Cassette Players Receiver AmplifiersRemote Control Quick Reference Functional Key Control KEY Mode FunctionDTV Mode Function KEYTroubleshooting Symptoms ChecksCleaning Specifications Memo Memo Customer’ Record