Panasonic PT 40LC12, PT 45LC12 Accessories, Remote Control Battery Installation, Before Using

Page 7

Before Using

Accessories

(1) Remote Control

(EUR7603Z80)

(2)Batteries 2 “AA”

(3)RGB Cable (2 m) (LSJA0239-1 or LSJA0443)

(4)Accessory Air Filter (LSYC0239)

Remote Control Battery Installation

Requires two AA batteries (supplied).
1.Turn the Transmitter face down.	2.Install the batteries as shown in the	3.Replace the cover and slide in
Remove top cover by pressing	battery compartment.	reverse until the lock snaps.
down on marking and sliding cover	(Polarity + or – must match the
off in the direction indicated.	markings in the compartment).

Two AA size

Getting Started

Helpful Hint:

For frequent remote control users, replace old batteries with Alkaline batteries for longer life.

Precaution on battery use

Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.

Observe the following precautions:

1.Batteries should always be replaced as a pair. Always use new batteries when replacing the old set.

2.Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).

3.Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.

4.Battery replacement is necessary when the remote control acts sporadically or stops operating the projection display set.

Helpful Hint:

Whenever you remove the batteries, you may need to reset the remote control infrared codes. We recommend that you record the code on page 62, prior to setting up the remote.

7

Image 7

Contents USA Models No. PT-40LC12/PT-45LC12For assistance, please call 1-888-VIEW PTV843-9788 For assistance, please callImportant Safety Instructions For Projection display Important Safety InstructionsImportant Safety Instructions Model Number TrademarksOr send e-mail to consumerproducts@panasonic.com Declaration of ConformityTable of Contents Optional External Equipment Before UsingSafety Precaution Receiver LocationPrecaution on battery use AccessoriesRemote Control Battery Installation Before UsingLocation of Controls Illuminated Remote ControlLocation of Controls Front Controls and Terminals on the projection displayRear Connecting the Antenna / Cable to the RF in Terminal No VCR InstallationAntenna Connection Cable Connection InstallationOutput VideoOUT Connects VCRs and other peripheral equipmentPRDVDY/PPBB/PROUTY Video How to connect the AV Out TerminalsHD/CSYNC How to connect the PC Input TerminalsSignal Names for D-SUB 15P Connector Pin No Signal name GroundAnalog RGB signals that can be input Initial Setup Power on and OFFPower OFF Turning the Power on and OFFPower on / OFF Power onUse the Action button Flow Chart of Main menuTo set or go to next menu Itcode Flow Chart of Main menuReturning to the previous screen Manual SET Tuning channelsEnglish NenacableNochfound Tuning channelsPress to exit menu Channel Press to select Manual channel settingPress to add channels to memory Press to select channel To add channelTo delete channel Press to select channelChannel. or use Number keys DesiredTV status display Using the number keysInvalid operation notice feature Projection display operationAspect Controls During PC input, the mode switches between no MAL, TrueFull only Aspect Controls Searching for the desired channel Channel search When a channel button is pressed during channel searchPlaying peripheral equipment Turning the power on and switching input modesConfirming connections Freezing pictures MuteMute / Freeze / SAP Sound muteMono broadcast MTS Stereo and SAP broadcastMTS Stereo broadcast SAP broadcastSelect Modes Selecting the screen mode for split screenSplit screen Press toChanging the channel of the right screen Split screenSwapping left and right screens Display PIP screen Picture in Picture PIP ScreenSwapping Main and PIP screens Picture in Picture PIP ScreenChanging the channel of the PIP screen Selecting the screen size for PIP screenPress to select the screen mode Adjusting screen position and sizeFull mode Press to exit menu Size Adjusting screen position and sizePhase WidthAuto Audio AdjustmentsSpeech Balance Audio AdjustmentsBass TrebleCinema Picture AdjustmentsPicture Adjustments Or Or Lock FeatureChanging your secret code Press to set Press to select Lock FeaturePerform Enter Secret Code on DeactivatedRatings to be blocked. P Press to set Perform US Movies Ratings onYES or no View NR Not Rated ProgramsEnter Caption Closed CaptionsScreen Press to select Caption screen Closed CaptionsPress repeatedly to select Manual AdjustCVA Pidp a CableOn or OFF Weak Signal Display FeatureSET UP Press to display Channel screen OFF Screen turns solid blue when signal is absent or weakPress to display Video screen Video NR Noise Reduction FeatureVideo RGB VGAAutomatically changing screen size MovgafComponent Video Input Y, PB / Cb ,PR / Cr input terminals VGA or 480P VGA When RGB input signal is VGA 60Hz from PC RGB Input FeatureInformation screen Switching languages for displayInformation Press to select LanguageAir Filter should be cleaned about every 400 hours Cleaning the Air FilterCleaner Air Filter Replacement Cleaning the Air FilterClogged Air Filter Detection Replacing the lamp unit Lamp unit replacement periodImportant Points to keep in mind When code is known Infrared Remote Codes for Specific Components When code is not knownVCR Infrared Codes Index Maker Set Up NoCBL AUX Mode Function Quick Reference Functional Button ChartButton Button Mode Function Symptoms Checks Troubleshooting12-14 Specifications Customer Services Directory CleaningCarry-in or In-Home Service Limited WarrantyLimited Warranty Coverage Category Parts Labor ServiceChannel up / down buttons projection display SymbolsPower button/POWER indicator 10, 21 Index