Panasonic PT-D10000 specifications Specifications

S P E C F I L E

3-Chip DLP™ Projector

PT-D10000

Specifications

Main Unit
Power supply:	North America:	120 V AC, 15 A, 60 Hz
	Europe, Asia	220–240 V AC, 15 A, 50/60 Hz
Power consumption:		1,450 W (25 W in standby mode with fan stopped)
DLP™ chip:	Panel size:	0.95˝ diagonal (4:3 aspect ratio)
	Display method:	DLP™ device x 3 (R, G, B), DLP™ projection system
	Pixels:	1,470,000 (1,400 x 1,050) x 3, total of 4,410,000 pixels
Lens:		Optional powered zoom/focus lenses
Lamp:		250 W UHM lamp x 4
Screen size:		70 – 600 inches, 4:3 aspect ratio
		(70 – 300 inches with the ET-D75LE5, 4:3 aspect ratio)
Brightness *1:		10,000 lumens (four-lamp operation mode)
Center-to-corner uniformity *1:		90%
Contrast *1:		5,000:1 (full on/full off, in dynamic iris 3 mode)
Resolution:		1,400 x 1,050 pixels (Input signals that exceed this resolution will be
		converted to 1,400 x 1,050 pixels.)
Scanning frequency:	RGB:	Horizontal: 15 –100 kHz, Vertical: 24 – 120 Hz*2,
		Dot clock: 20–162 MHz
	YPBPR (YCBCR):	480i: fH 15.75 kHz; fV 60 Hz, 576i: fH 15.63 kHz; fV 50 Hz,
		480p: fH 31.50 kHz; fV 60 Hz, 576p: fH 31.25 kHz; fV 50 Hz,
		720/60p: fH 45.00 kHz; fV 60 Hz, 720/50p: fH 37.5 kHz; fV 50 Hz,
		1035/60i: fH 33.75 kHz; fV 60 Hz, 1080/60i: fH 33.75 kHz; fV 60 Hz,
		1080/50i: fH 28.13 kHz; fV 50 Hz, 1080/25p: fH 28.13 kHz; fV 25 Hz,
		1080/24p: fH 27.00 kHz; fV 24 Hz, 1080/24sF: fH 27 kHz; fV 48 Hz,
		1080/30p: fH 33.75 kHz; fV 30 Hz, 1080/60p: fH 67.5 kHz; fV 60 Hz,
		1080/50p: fH 56.25 kHz; fV 50 Hz
	S-Video/Video:	Horizontal: 15.75/15.63 kHz, Vertical: 50/60 Hz,
		(NTSC, NTSC4.43, PAL, PAL60, PAL-N, PAL-M, SECAM)
Optical axis shift*:	Vertical:	±50% (±40% with the ET-D75LE6) from center of screen, powered
	Horizontal:	±30% (±20% with the ET-D75LE6) from center of screen, powered
Keystone correction range:		Vertical: ±40° (±22° with the ET-D75LE5, ±28° wih the ET-D75LE6)
Installation:		Ceiling/floor, front/rear
Terminals:	DVI-D IN:	DVI-D 24-pin x 1, DVI 1.0 compliant, HDCP compatible, single link
	RGB1 IN:	BNC x 5
	R, G, B:	G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms,
		B, R: 0.7 Vp-p, 75 ohms
		HD, VD, SYNC: 1.4–5.0 Vp-p, positive/negative automatic
	Y, PB, PR	Y: 1.0 p-p, 75 ohms (incl. sync signal), PB/PR: 0.7 Vp-p, 75 ohms
		0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms
		NOTE: HD/SYNC, and VD terminals do not accept 3-value direct sync signals.
	RGB2 IN:	D-sub HD 15-pin x 1
	R, G, B:	0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms
		HD, VD, SYNC: TTL, high impedance, positive/negative automatic
		VD: 1.4–5.0 Vp-p, positive/negative automatic, 75 ohms
	Y, PB, PR	Y: 1.0 p-p, 75 ohms (incl. sync signal), PB/PR: 0.7 Vp-p, 75 ohms
		NOTE: HD/SYNC, and VD terminals do not accept 3-value direct sync signals.
	VIDEO IN:	BNC x 1, 1.0 Vp-p, 75 ohms

As of November 2008 < 2 >