Panasonic PV-HS2000 operating instructions Input Settings

Page 52

Troubleshooting (continued)

PROBLEM

SOLUTION

I’m having problems changing

• If your original remote control required an Enter button press when

channels.

changing channels, press the ENTER button on the Hard Disk

 

Recorder remote control after you enter the channel number.

 

 

Only one device’s volume control

• Refer to “Changing Volume Lock” on page 42 and unlock the volume

code is sent regardless of which

controls.

mode I have put the remote control in.

 

 

 

I’m using an IR blaster to control my

• This may be dependent on how many digits you needed to enter to

cable box or satellite receiver and I’m

tune to a specific channel using the remote control for your cable box or

having trouble changing channels

satellite receiver, prior to hooking up the Hard Disk Recorder. For

using the Hard Disk Recorder remote.

example, if you needed to enter 0 - 5 to tune to channel 5, you need to

 

“tell” the Hard Disk Recorder this information during the on-screen

 

setup. To update this information, go back to Setup to adjust the

 

code for your cable box or satellite receiver.

 

1. Press the MENU button on the Hard Disk Recorder remote.

 

2. Choose Setup from the Main Menu, then choose Change Dialing &

 

Input Settings.

 

3. From the Setup Summary screen, choose the input that your cable

 

box or satellite receiver is connected to.

 

4. Proceed through the steps to configure your box until you reach the

 

screen that asks for your cable box or satellite receiver setup code.

 

5. Press the button to clear the setup code:

 

A. If your unit required 2 digits to tune to a one-digit channel, enter

 

the code for your unit but replace the first digit with the number 6.

 

B. If your unit required 3 digits to tune to a one-digit channel, enter

 

the code for your unit but replace the first digit with the number 8.

 

Refer to “Code Numbers For Your Components” on pages 47 and 48

 

to find your code.

 

6. Continue through the remaining screens and complete the setup.

 

7. Once you have completed setup, try changing the channels on

 

your cable box or satellite receiver.

 

8. If you are still having trouble changing channels, repeat step 5

 

above with the following changes:

 

• If you used step 5A, replace the number 6 with the number 7.

 

• If you used step 5B, replace the number 8 with the number 9.

 

 

My cable box sometimes fails to

• If you are using the IR blaster, your cable box receives IR commands

change channels when using the

from both the Hard Disk Recorder remote and the IR blaster. Some

Hard Disk Recorder remote control.

cable boxes can be confused by this. You can prevent your cable box

 

from receiving the commands from the Hard Disk Recorder remote

 

control by affixing an opaque covering around the area where you

 

have placed the IR emitter on your cable box. Don’t cover the IR

 

emitter.

 

 

The Hard Disk Recorder does not

• Press and hold the power button on the front of the unit for 10

respond when I press buttons on the

seconds, then release. The Hard Disk Recorder will start up in a few

remote control. Or, the image on my

moments.

television screen is “frozen.”

• Unplug the power cord for 15 seconds then plug it back in. The Hard

 

 

Disk Recorder will restart and power on in a few moments.

 

 

52

Page 51 Page 53
Image 52
Page 51 Page 53
Contents Model PV-HS2000 MailConsumerproducts@Panasonic.comOutdoor antenna grounding Moving a product-and-cart combinationDo not place heavy objects on the Hard Disk Recorder Precautions Patent Nos ,631,603.4,577,216.4,819,098 and 4,907,093Table of Contents Welcome to the Hard Disk Recorder Before Using Installing the BatteriesImportant Notes Connecting the incoming television signal Using wireless phone jacksBasic Connections Modifying an older type antennaConnecting a composite-video television Connecting the telephone lineConnecting the AC Power cord Complete the on-screen setupAdvanced Connections Planning Input and Output ConnectionsConnecting a Cable Box to the Hard Disk Recorder Receiver Satellite Receiver OUT Outp UT Connecting a Serial Cable Attaching Satellite Receiver and Cable Box ControllersConnecting and Setting Up the IR Blaster Locating the Infrared Detector On the Other DeviceInitial Setup If the connection failed Changing Your Setup Later On Press Play to begin using the Hard Disk RecorderInput Options Completing the IR Blaster SetupPress Number buttons Using Instant Replay Press TV, then press Power to turn on your televisionControlling Live Television Viewing Live TelevisionPausing Live Television and Recorded Shows Using Rewind and Fast ForwardUsing Slow Motion Using Frame AdvanceUsing QuickSkip Bypassing unwanted programmingViewing copy protected programming Copy Protection InformationCable Box Splitter Hard Disk Recorder Recording Shows Selecting a ShowChannel Guide Screen Channel Guide Popup Menu Items Press / / / to move around the guideWatching and Recording a Show That Is Currently Airing Recording a Single Upcoming ShowPress REC to record the show Extending Recording TimeRecording Multiple Episodes of One Show Cancelling a RecordingRecording is not in progress Setting the Recording Options Record Options SettingsRecording From Show Categories Press Replay Zones to display the ReplayZones screenRecording Shows Based On a Theme You Choose Create a Theme , then press Select to select itTo Record One of the Shows To Cancel Recording of a ShowTo Create a Show-based Replay Channel Finding Shows Finding All Episodes of a Show Show-based Replay ChannelsTheme-based Replay Channels Press ChannelWatching Your Recorded Shows Press Replay Guide to display the Replay Guide Seeing What a Replay Channel Will RecordFind matching shows, then press Select Watching a Show Programming blocked by V-Chip technologyWatching shows with closed-captioning PressPreserving a Show Press / to select the show you want to saveReplay Guide, then press Select Preserve this episode, then pressPress / to select Save to VCR, then press Saving Shows to VideotapeBefore you begin Guaranteed and Non-guaranteed Recording Indication of Guaranteed or Non-guaranteed recordingManaging Recording Space Recording PrioritiesGuaranteed Record and Space-available Record Recording Space Management TipsUniversal Remote Control Changing Volume LockSetting Up Your Components To change the volume lock setting back to TV modeSearching for Your Component’s Code To reassign other component mode buttons Re-assigning Component Mode ButtonsLearning the Codes Programmed Into the Remote Code Numbers ForYour Components TVsCode Numbers For Your Components VCRsSatellite Receivers VCRsDVD Players Cable BoxesLaser Disks TV/VCR Combos Important NoteTroubleshooting Problem SolutionHard Disk Recorder, shows appear Input Settings Specifications & Information SpecificationsResetting Hard Disk Recorder Screen BurnSoftware License Agreement License Grant RestrictionsWarranty Panasonic Hard Disk Recorder Products Limited WarrantyService Center List Regulatory Notices for the U.SFront View of the Hard Disk Recorder Location of ControlsRear View of the Hard Disk Recorder FF Fast Forward Remote Control Buttons33 TV/ VCR Volume Up/Down Code SetNumber buttons Channel GuideOne Panasonic Way Secaucus New Jersey
Top Page Image Contents