Sylvania 6260VF owner manual Before Using Your VCR, HintHint

RF Output Channel

	If you need additional operating assistance after
	reading this owner’s manual or to order replace-
Owner’s Manual	ment accessories, please call
	TOLL FREE : 1-800-968-3429
Video Cassette Recorder	or visit our web site at
6260VF	http://www.SylvaniaConsumerElectronics.com

1. Before Using Your VCR

If channel 3 is already occupied for broadcasting,

1)Set your TV to channel 4.

2)Insert a pre-recorded tape into this unit.

3)Hit [PLAY B] once.

4)After a few seconds, hold [PLAY B] on the unit for 3 seconds.

•The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.

•When a picture does not appear on the TV screen, repeat step 4).

5)Hit [STOP C] to stop playback.

HintHint

•The RF output channel may not change when you adjust tracking during playback. In this case, stop the playback, and start the playback again. After that, hold [PLAY B] on the VCR for 3 seconds again.

Basic TV Connection

Stereo TV Connection

You can use the AUDIO OUT jacks

and VIDEO OUT jack on the back of

VIDEO AUDIO IN
IN	L	R	AUDIO	ANT
			L	IN

OUT IN

Cable TV Antenna	Cable TV Antenna
Signal	Signal

(Back of VCR)

the VCR if your TV has Audio/Video

R

VIDEO

OUT

or or

	(Back of TV)
Disconnect	2
	Connect

(Back of TV)

ANT
IN	3
OUT
	Connect

Input jacks. In this case, you need to
set the TV to external Line Input
Mode. Please refer to your TV’s
owner’s manual.	(Back of TV)

OUT IN

Audio/Video Cables

(not supplied)

(Back of VCR)

Front & Rear Terminals

RF Cable (supplied)

4 Plug the AC power cords of the VCR and TV into the AC outlets.

AUDIO OUT jacks

Connect the audio cables here through to the audio input jacks of a camcorder, another VCR, a stereo amplifier, a stereo amplifier or an audio system.

AUDIO IN jacks

Connect the audio cables coming from the audio output jacks of a camcorder, another VCR or an audio source here.

AUDIO	ANT	ANT IN jack
	IN

Hint for Cable Box or Satellite Box

AUDIO

L

ANT

IN

LConnect your antenna or cable box here.

OUT IN

OUT IN

R

VIDEOOUT

R ANT OUT jack

	(Cable	box or		(Back of VCR)
Antenna or			ANT
Cable TV	Satellite box)		IN
	IN OUT
signal			OUT	RF cable	E
				(supplied)

(Back of TV)

Select this connection when you want to view or record a scrambled channel. With this con- nection, channels cannot be changed on the unit. You can view or record ONLY the chan-

To select channels of the cable box or satellite box

1) Turn on the unit by hitting [POWER], then
hit [VCR/TV].The “POWER” and the
“VCR/TV” indicator on the front panel will
appear, then press [CHANNEL	] to
select channel 3 or 4 (the same channel as
the output channel of the cable box or
satellite box).
• If you use the channel 4, you need to

OUT IN

VIDEO OUT jack

Connect the video cable here through the video input jack of a camcorder, another VCR or a TV.

	POWER	CHANNEL				MEN
VIDEO	L - AUDIO - R	POWER	VCR/TV	TAPE IN	TIMER	REC

VIDEO	OUT	Connect the supplied RF cable to the
OUT IN		antenna input jack on your TV.

VIDEO IN jack

Connect the video cable coming from the video output jack of a camcorder, another VCR or an audio-visual source (laser disc player, video disc player, etc.) here.

nels you have selected on the cable box or the satellite box.

• While you are recording, only the recorded channel can be viewed.

	change the unit’s RF output to channel 4.
	Refer to “RF Output Channel”.
2)	At the TV, select channel 3 or 4 (the same
	channel as you have selected at step 1).
3)	On the cable box or satellite box, select the
	channel you want to view or record.

Supplied Accessory

• Remote control	• RF cable	• Owner’s manual
(NA376UD) with	(WPZ0901TM002)	(1VMN20688)
two AA batteries

Installing the Batteries for the Remote Control

Install two AA batteries (supplied) matching the polarity indicated on the bottom of the remote control.

	Printed in China
- 1 -	1VMN20688 / HJ411UD ★★★★★