JVC AV-20FD22 manual Inserting Batteries, Operation

Page 10

Remote control

Inserting Batteries

1 Slide the battery compartment cover in the direction of the arrow.

2 Install two "AA" batteries

3 Replace the compartment

(supplied), paying attention to

cover.

the polarity diagram in the

 

battery compartment.

 

BATTERY PRECAUTIONS

The precautions below should be followed when using batteries in this device:

1.Use only the size and type of batteries specified.

2.Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may cause damage to the device. To avoid a potential short circuit, insert the “–end” first.

3.Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.

4.If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.

5.Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery manufacturer’s directions.)

6.When you change the batteries, try to complete the task within three minutes. If you take longer than three minutes, the remote control codes for your Cable Box may have to be reset (see page 50).

REMOTE CONTROL BASICS

Before you can operate the remote control, you must first install the batteries (included). See “Inserting Batteries” on this page above for instructions.

Press the POWER button to turn the television on or off.

Make sure the TV/CATV switch is set to TV. Move the switch to CATV only if you need to operate a cable box. (You must set the remote control to operate a cable box. Please see page 50 for instructions.)

Press the CH + and CH – buttons to scan through the channels. Tap the CH + or CH – button to move through the channels one channel at a time.

Press VOL + or VOL – to raise or lower the volume. An indicator bar will appear onscreen to show you the television volume level.

The CH +/– and VOL +/– buttons are also used to navigate JVC’s onscreen menu system.

You can directly access specific channels using the 10-key pad.

This remote includes illuminated buttons for key features like CH +/– buttons, and VOL +/– buttons. Press the LIGHT button to turn the illumination on.

Each press of TV/DVD on the remote control, switches the screen between the TV screen (TV mode) and the DVD screen (DVD mode). You can operate a TV and TV menu in the TV mode, and a DVD and DVD SETUP menu in the DVD mode.

Operation

• Aim the remote control at the remote sensor and press control buttons to operate.

• Operate the remote control within 30° angle on either side of the remote sensor, up to a dis- tance of Approx. 5 meters.

Approx. 5 meters

10

Image 10
Contents TV/DVD Combo Users Guide Serial NumberRisk of Electric Shock Do not Open Power Sources CleaningAccessories Read InstructionsDamage Requiring Service POWER-CORD ProtectionPower Lines Replacement PartsPower Source Horizontal Resolution FeaturesDigital Audio Jack Coaxial Contents Front HOW to Open the Front DoorParts and functions RearRemote control TV / DVDInserting Batteries OperationAntenna connections For Subscribers to Scrambled Cable TV Service For Subscribers to Basic Cable TV ServiceCable TV connections Enter Setting the languagePress TV Menu until the Menu screen is cleared TV operation MutingDisplay Sleep TimerChannel UP/DOWN TV ReturnWhat is Closed CAPTIONING? Closed captionTo memorize channels TV VHF/UHF channels Catv Cable TV channelsChannels available in your area Press or to select the AutoCH MEMORY, then press or TV will begin memorizing all Press TV Menu until the MenuTo Register Password Setting the V-ChipIf you forget the password, you can- not set the V-Chip Press To select To SET the V-CHIPOFF Can ENG RATING, then pressTo Change Password Press TV Menu repeatedly to return to normal screenPress or to select the item you want to adjust Picture control adjustmentCancel Contrast default setting is set to maximum at the factoryTo Select Desired Sound Stereo and separate audio program SAPCertain the SAP appears on Press Audio to select Desired soundBass Sound control adjustmentCancel TrebleDisc DVD mode Reading changes no Setting setup languageSetup language can be selected Stop mode Press To select OtherPress OPEN/CLOSE on the unit. The disc tray will open Playback procedurePress Play or OPEN/ Close on the unit Special playback Zooming ZoomingPress Zoom during play Audio CD Repeat playbackTitle, Chapter, Track Playback Repeat PlaybackRandom playback Program playback/Random playback Audio CDProgram playback You can arrange the order of tracks on the discChanging soundtrack language Turning the Subtitles On and Off SubtitlesChanging the subtitle language Title Selection Changing angles / Title selection / DVD menuChanging Angles DVD MenuPress number buttons 0-9 to input a 4-digit password Parental control settingOr Enter To change the parental level Press DVD Setup in the stop mode or No DiscNumber buttons 0-9 to Temporary disabling of rating level by DVD disc PAN Scan Setting the aspect ratio of TV screenYou can select the aspect ratio for your TV Wide ScreenSelect on or OFF Setting on Screen display/Status display of DiscPress / or Enter to DVDSetting menu language English, Francais, EspanolOther Setting subtitle languagePress or ENTER, then Press or to select Subtitle AutomaticYour desired Audio Lan Setting audio soundtrack languageAudio Guage, then press EnterLanguage Code List Connections to other equipments Using an Audio AmplifierUsing an AV Amplifier with built-in digital surround Rear of TV/DVDUsing the audio/video inputs VCRSymptoms Possible Solutions Power Problems and troubleshootingTV Broadcast Reception Symptoms Possible Solutions DVD Remote ControlReception disturbances IgnitionTelevision SpecificationsGeneral DVD/CD playerSetting the Catv Codes Cable Box or Satellite setupMemo JVC Company of America JVC CANADA, INC 5870201A 01/03