DivX Sub, Front, Center, Surround, Delays

KH6510_11_A4_V3_EN.qxd 24.08.2006 12:25 Uhr Seite 11

KH 6510/6511

-DVD Subtitle: Here you set the language of the subtitle when the playback of a DVD is displayed on the television screen (only if the langu- age is present on the DVD).

-Audio:Here you set the language, in which the DVD should be started. Films can then only be played back in the language that you selected if this language is available on the DVD. If the selected language is not available the DVD will start with another language.

-DivX Subtitle: Here you set the character encoding for the DivX Subtitle. The standard setting is Western European.

-DivX Sub

Position: Here you set the position (Bottom/

Middle/Top) of the DivX Subtitles.

8.3. Video settings

In this OSD Menu you can administer the settings for Image format, Screen Mode, TV-Standard, Video-Output, Brightness and Sharpness.

•Then keep pressing the button "Video Out" on the remote control until the Image reappears on the television screen.

-Brightness: Here you set the Brightness (1-16) of the DVD player.

-Sharpness: Here you set the contrast (1-16) of the DVD player.

8.4. Audio settings

In this OSD-Menu you can administer the settings for Bass Management, the size of individual loud speakers, Test Sound, Delays, Digital Audio Outputs, Night Mode and ProLogic.

-Aspect Ratio: Here you set the Image format, in which the film should be displayed on the tele- vision screen (4:3 or 16:9). The correct setting depends on the television to which you would like to connect the DVD player.

-Viwe Mode: Here you can adapt the Height and width of the Image to the playback device being used, for example Pan & Scan (Adapta- tion of Image width formats to the 4:3 Image).

-TV-System:Here you set the TV-Standard (PAL/NTSC/ Multi) of your playback device. Only set "Multi" if you have connected the DVD player to a Multi standard television.

-Video out: Here you set the Vidio-Output, through which the DVD player is connected to the playback device.

IMPORTANT!

In the event that you set an incorrect Vidio-Output, for example "P-Scan", although your television is not capable of Progressive Scan, then the television screen will suddenly become black. This is not a defect of the television or the DVD player!

In a case such as this...

• Press the "Stop" button on the front panel of the DVD player or on the remote control.

-Bass management: Here you can Activate/Deactivate the Bass-Management. Activation (on) is necessary if you are not using a 5.1 am- plifier with its own speaker management but rather want the sound output trans- mitted via a particular amplifier. In this case the DVD player must be informed which kind of speaker (Small/Large) is to be run from the respective sound output. In this way the sound and the separation of Highs, Middles and Basses can be opti- mally conformed.

-Front, Center, Surround,

Subwoofer LS: Here you can Activate/Deactivate the

particular speaker type and set the size. Large: Bass activated.

Small: Bass deactivated.

(only with the activation of Bass-Management)

Small: No speaker connected

-Test tones: Here you can switch on a test sound for each particular audio output in order to check your 5.1 Surround settings.

-Delays

Center, Surround: Here you set the delays for the Centre

speaker and the rear Surround speakers. Each increase in the distance setting cor- responds to a delay of one millisecond.

With optimal settings the sound reaches your listening location at the same time from all directions.

Centre: No delays, 0.3, 0.6, 1, 1.4, 1.7 m.

Surround: 1, 2, 3, 4 or 5.1 m

- 11 -