Mintek 27HL85 owner manual Adding channels to the TVÕs memory, Programming channels automatically

Page 24

Adding channels to the TVÕs memory

When you press Channel y or z, your TV will stop only on the channels you program into the TVÕs channel memory.

Follow the steps below and on the next page to program all active channels into the TVÕs memory.

Programming channels automatically

Your TV can automatically detect all active channels in your area and store them in the channel memory. After the channels are

Note:

To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control.

TV/VIDEO RECALL POWER

INFO

programmed automatically, you can manually add or erase individual channels (see page 30).

To program channels automatically:

1.	Press MENU, and then press x or • until the SET UP menu
	appears.
2.	Press y or z to highlight TV/CABLE.

1

4

7

+10

100

			NU
			E
		P	M	ORITE
T	O	P		ORITE
	O
			FAV
			FAV

2

5

8

0

FAV

3

6

9

CHRTN

ENT

		G
		UI
	PIC	D
	PIC	E
		E
	SIZE

Setting up your TV

3. Press x or • to select either TV or CABLE, depending on which

you use. If you use an antenna, select TV; if you use cable

channels, select CABLE.

SET UP	1/2

LANGUAGE	ENGLISH

TV/CABLE	CABLE

CH PROGRAM	ENTER

ADD/ERASE	ADD

CH LABELING	ENTER
VIDEO LABEL

MENU BACK EXIT WATCH TV

4. Press z to select CH PROGRAM.

SET UP	1/2
LANGUAGE	ENGLISH
TV/CABLE	CABLE
CH PROGRAM	ENTER
ADD/ERASE	ADD
CH LABELING	ENTER
VIDEO LABEL

MENU BACK EXIT WATCH TV

5.Press ENTER to start channel programming. The TV will automatically cycle through all the TV or Cable channels (depending on which you selected), and store all active channels in the channel memory.

While the TV is cycling through the channels, the message ÒProgramming NowÑPlease WaitÓ appears.

6.When channel programming is complete, the message ÒCompletedÓ appears.

7.Press Channel y or z to view the programmed channels.

MENU

DVDMENU

	ENTER			EXIT		R
N				EXIT		R
E
T		FAV			A
	E	FAV			A
	R			LE
	R			C
TV		CH	VOL
CBL/SAT		CH	VOL
VCR
DVD
	POP DIRECT CH MUTE			SLEEP
TV/VCR		PAUSE	STOP	PLAY
		FREEZE	SOURCE	SPLIT
REW		FF	SKIP/SEARCH
CH SCAN		SWAP	POP CH
	REC			LIGHT

MENU

yzx •

ENTER Channel yz

24

Image 24

Contents 27HL85 Safety Precautions Dear CustomerImportant Safety Instructions InstallationService Care cont. from previous columnImportant notes about your LCD TV Introduction Supplied accessories Check that you have the accessories and items shownIntroduction Welcome to ToshibaExploring your new TV VideoConnecting your TV Connecting an antenna or cable TVChannels Connecting a VCR Connecting a cable converter box and VCRConnecting a DVD player or satellite receiver and a VCR Introduction Connecting yourTVDVD player with component video For Hdmi or DVI connection, see Connecting two VCRs Connecting a camcorderConnecting an HDMIª or a DVI device to the Hdmi input ¥ one Hdmi cable type a connector¥ one HDMIÐtoÐDVI adapter cable Hdmi type a connector ¥ one pair of standard analog audio cablesUsing the remote control Preparing the remote control for useInstalling the remote control batteries Remote control effective rangeRemote control codes For future reference, write down the codes you usedRemote control codes Introduction Connecting YourTV Control Remote Control function key chart CLEAR/EXITLearning about the remote control Connecting YourTV ControlSetting up your TV Learning about the menu systemChanging the on-screen display language Press x or to highlight your desired languageAdding channels to the TVÕs memory Programming channels automaticallyChanging channels Adding and erasing channels manuallyUsing the TVÕs features Adjusting the channel settingsSwitching between two channels using Channel Return Programming your favorite channelsConnecting Labeling channels Viewing the wide-screen picture formats Selecting the picture sizeTheaterwide 1 picture size For 43 format programs Adjusting the Picture SIZE/POSITION Using the Auto Aspect feature Press y or z to highlight Auto AspectPress x or to select on Using the Gray screen function Selecting the gray level of the side panelsUsing the Locks menu Using the V-CHIP menuEntering the PIN code If you cannot remember your PIN codeOFF To release your setting Unlock TV Rating Independent rating system for broadcastersTV Rating menu appears Press z or y to select an item Repeat steps 2 and 3 to set the next itemMpaa Rating Independent rating system for movies Chip menuLocking channels Unlocking programs temporarilyRepeat steps 2 and 3 for other channels Repeat for other channels Locking the video inputs Changing the PIN codeAdjusting the picture Selecting the picture modeAdjusting the back light feature Press x or to select the mode you preferAdjusting the picture quality Using the Black stretch featureUsing the Mpeg NR feature Using the CableClear¨ DNR featurePress x or to select HIGH, MIDDLE, LOW, or OFF Selecting the color temperature Selecting the cinema modeSelecting the video input source Labeling the video input sourcesUsing the closed caption feature Press x or to highlight C1-C4 or T1-T4¥ To view text, highlight T1, T2, T3, or T4 Setting the sleep timer Setting the on timerAdjusting the sound Muting the soundSelecting stereo/SAP broadcasts Using the WOWª surround sound feature Adjusting the sound quality Using the StableSound¨ featureTo turn off the StableSound feature Select OFF in above Understanding the auto power off feature Understanding the last mode memory featureDisplaying on-screen information Specifications AppendixTroubleshooting AntennaBlack box appears on the screen T2, T3, or T4. Turn closed captioning OFFLimited United States Warranty Limited Canada Warranty Index Channel programmingToshiba ELECTROMEX, S.A. DE C.V