Dolby Laboratories RC2888/01, RC2573GR Antenna connection, Mains connection, Switching on the TV

Page 8

4.Basic TV connections

4.1Antenna connection

Connect the antenna or RF cable signal to the 75 Ω RF ‘:’ connector socket located on the TV.

4.2Mains connection

Ensure that the mains voltage and frequency are correct. Refer to the product labelling and documentation.

D Note: The power button . on the TV does not disconnect the television from the AC mains. It toggles the TV between on and stand-by mode.To completely turn off the TV you must unplug the AC mains plugs from the wall socket.

4.3Switching on the TV

Press . on the TV or on one of the optional remote controls to switch the TV set on.

Image 8

Contents Table of Contents Important safety instructions Read Before Operating EquipmentKnow these safety symbols U T I O NSafety information and useful tips Pull the power lead by the plug do not pull by the wireBefore calling service Symptoms Suggested stepsConfiguring the control options on Deselect HM Link in the Communication Mains connection Switching on the TVAntenna connection Overview of TV Connectors and controls MenuSpdif RC2888/01 Optional remote controlsRC2573GR Description of guest remote control Setup Overview of TV menusAccessing the setup menu Accessing TV Setup Menu using the Remote Control RC2573GRSlide the button to the Setup location To scroll through the menuInstallation Selecting the languageSelecting the communication source SP SPI SP I2CChanging the settings of a channel Press Æ to enter the Channel Install menuChannel Install Select a ChannelTUNER,AV, SVIDEO, CVI, VGA, HDMI1, HDMI2, CARD-CVBS Side SvideoPress 0 9 to key in the channel number 1 to Selecting your Preferred RingNaming a channel Selecting the Mute SourceSelecting cable or antenna mode Select YES to use Cable mode and no to use Antenna modeAuto Install TV Cable Tuning YESSetting options for digital channels To enable Current RING, select from RING1 to RING4Press Æ to enter the Digital Setup mode Selecting a virtual or physical channelSetting up the Vchip / Digital Rating and Factory CH Reset Press Æ to enter the Channel Setup modePress Æ to enter the Audio mode Selecting the Digital Audio languageSelect on option to enable Emergency Alert Activating the Emergency AlertPress Î or ï to select the item you want to configure Press Î ï to select the item you want to configureSpecifying the conﬁguration when switching on TV Sound FullscreenChannel Display Press Æ to enter the Security menu Press ï to select Remote Control LockPress ï and select Security Press ï to select Decryption ControlPress Æ to enter the Decryption Control menu Press Æ to start conversionUsing V-Track to watermark Time Setting option allows you to manually enter the timePress Æ to enter the Vtrack menu Conﬁguring the control optionsDigit Timeout Control ESP OFFControl ESP Digit Entry YESPress Æ to enter the Features menu Press Æ to enter the Video Adjustment menuConﬁguring the features options and settings Select and configure the settings and options for Select Smart Sound to listen to different Smart Sound modesSoftware downloading and cloning Select SW DownloadUSB Source ALL Clone Data SSB NVMStandby Firmware only download Iboard NVMUSB device RF SourceALL SSB NVM SW Download SourceCC / V-CHIP CC / V Chip Save CCDigital CC Mode option Analog CC Mode option, itOFF and on Mute V-CHIP Menu Item optionCOLOR, RELAXED, MODERATE, Dynamic 10.10Change Ambilight settingsConﬁgure Ambilight Press to exit CustomLOW, MED and High Support for multiple remote controls Programming the Multi Remote Controls functionAppendix a CommunicationDefinitions, acronyms and abbreviations CvbsOSD STB Philips’ Commercial Television USA limited warrantyPhilips F1rst Choice Limited Warranty What WE will do to Correct PROBLEMS? Page Just a phone call away Do not rub with dust clothes containing chemical treatment Cleaning and careEnvironmental care Index Page Page If present Dolby DigitalKensington Security Slot