FUNAI MSD513E owner manual SET UP for USE, Selecting the Language, Channel SET UP

Page 13

SET UP FOR USE

TV SECTION

SELECTING THE LANGUAGE

TV

1Plug in the TV/DVD power cord

Plug the TV/DVD power cord into a standard AC outlet.

NOTE:

If any digits appear in the corner of the screen, press POWER without unplugging the power cord.

Make sure ...

Press POWER to turn on the TV/DVD.

NOTE: This function effects only the language on the screen menu and not the audio source.

2 Select “LANGUAGE”

- TV SETUP -

Press SETUP on the remote control.

CHANNEL SET UP

Press Arrow (K/L) to point to

V-CHIP SET UP

B LANGUAGE [ENGLISH]

CAPTION [OFF]

“LANGUAGE”.

 

3Select “ENGLISH”, “ESPAÑOL” or “FRANÇAIS”

Select “ENGLISH”, “ESPAÑOL”= Spanish or “FRANÇAIS”= French using ENTER.

4Exit the Language mode

Press SETUP to return to TV mode.

NOTE: If for some reason the menu is in Spanish or French, press SETUP, press Arrow (K/L) to point to “IDIOMA [ESPAÑOL]” or “LANGAGE [FRANÇAIS]”, then press ENTER, then press SETUP on the remote control.

CHANNEL SET UP

TV

You can program the tuner to scan all the channels you receive in your area.

NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just select the TV/DVD channel selector to the output channel of the cable box or satellite box (Ex CH3), then select the channel to be viewed on the Cable Box or Satellite Box.

Make sure ...

Press POWER to turn on the TV/DVD.

1 Select “CHANNEL SET UP”

 

Press SETUP on the remote control.

- TV SETUP -

Press Arrow (K/L) to point to

B CHANNEL SET UP

“CHANNEL SET UP”.

V-CHIP SET UP

LANGUAGE [ENGLISH]

Then press ENTER.

CAPTION [OFF]

 

2 Begin auto ch programming

 

Press Arrow (K/L) to point to

– CHANNEL SET UP –

“AUTO CH PROGRAMMING”.

ADD / DELETE CH (CATV)

Then press ENTER.

B AUTO CH PROGRAMMING

The tuner scans and memorizes all

 

the active channels in your area.

 

3After scanning

The tuner stops on the lowest memorized channel.

When AUTO CH PROGRAMMING is activated where there is no TV signal input, “NO TV SIG- NALS” will appear on the display after the com- pletion of the channel scanning.

The TV/DVD may recognize TV channels to be CATV channels by the receiving conditions. In this case, try auto ch programming again in the fine receiving conditions.

– 13 –

EN

0C28

Image 13
Contents OWNER’S Manual Important Safeguards S2 8 9 8 a Laser Safety PrecautionsImportant Copyright Information RADIO-TV InterferenceLocation Supplied AccessoriesAvoid the Hazards Electrical Shock and Fire Table of Contents TV Mode FeaturesTV/DVD Front Panel Operating Controls and FunctionsTV/DVD Rear View Installing the BatteriesANTENNA/CABLE Connections Preparation for USEVHF/UHF Combined Antenna VHF/UHF Separate AntennasConnecting to AN Amplifier Equipped with Digital Connecting to External Input JacksConnecting to a Dolby Digital Decoder for DVD Channel SET UP SET UP for USESelecting the Language Deleting or Adding Channels Watching a TV Program TV OperationDegaussing Picture ControlTo Cancel the Closed Caption System Sleep TimerWhen the Closed Caption Mode is on To cancel the sleep timerTV Rating SET UP Chip SET UPWhen you select TV-Y7 When you select TV-PG, TV-14 or TV-MAChange Access Code Mpaa Rating SET UPPlayable Discs Disc Types About the DiscsDVD Audio CDPlaying a Disc Basic Playback General FeaturesDisc Menu Title MenuPause ResumeStep by Step Playback Fast FORWARD/REVERSE SearchSearch Function Marker Setup ScreenTrack Search Time Search Title / Chapter SearchRepeatprogram Special Playback FunctionRandom Playback MP3 Playback Playing a MP3 DiscProgram RepeatChanging the Settings DVD-V CD MP3 ON-SCREEN InformationLanguage Setting Changing the DVD Setup ItemsWhen playing disc with copyright Protection Display Setting Audio SettingsEnter Initialize Parental ControlProblem Corrective Action Troubleshooting GuideDVD Closed Caption Problem Possible RemedyCabinet Cleaning MaintenanceDisc Handling ServicingGeneral Specifications SpecificationsElectrical Specifications Other SpecificationsConsulte la figura 1 de la página Controles DE Operación Y FuncionesConsulte la figura 2 de la página Consulte la figura 3 de la páginaPara Insertar LAS Pilas Preparación Para LA UtilizaciónConexiones DE ANTENA/CABLE Antena Combinada DE VHF/UHFConexión a UN Conexión a Tomas DE Entrada ExternaAntena Separadas DE VHF/UHF Para VER UN Canal CODIFICADO/DECODIFICADOSelección DE Idioma Conexciona UN Decodificador DolbyConsulte la figura 7 de la página Reproduccion Basica Ajuste DE CanalAjuste DE Canal Autoprogramacion DEMemo Tel DurationPlease do not Ship Your Unit to the Teterboro Address