Symphonic SC513DF Channel SET UP, Auto Channel Programming, ADDING/DELETING Channels, Enter

Page 15

CHANNEL SET UP

Make sure ...

TV

The unit must be turned on.

AUTO CHANNEL PROGRAMMING

As the initial setting, this unit has memorized all channels, including the ones not available in your area. This feature automatically puts only available channels into the memory.

1 Select “CHANNEL SET UP”

- TV SETUP -

Hit [SETUP].

B CHANNEL SET UP

Press [K / L] to point to

V-CHIP SET UP

LANGUAGE [ENGLISH]

 

CAPTION [OFF]

“CHANNEL SET UP”, then hit

 

[ENTER].

 

 

 

2 Begin channel scanning

 

Press [K / L] to point to “AUTO

– CHANNEL SET UP –

CH PROGRAMMING”, then hit

ADD / DELETE CH (CATV)

[ENTER].

B AUTO CH PROGRAMMING

 

The tuner scans and memorizes all

 

the active channels in your area.

 

3After scanning

The tuner stops on the lowest memorized channel.

NOTES:

When “AUTO CH PROGRAM- MING” is activated where there

is no TV signal input, “NO TV

NO TV SIGNALS

SIGNALS” will appear on the

 

 

display after the completion of

 

channel scanning.

 

The unit may recognize CATV channels to be TV channels if reception condition is poor. In this case, check the antenna connection and try “AUTO CH PROGRAMMING” again when reception condi- tions are better.

Channel memory programming is NOT neces- sary when connected to a cable box or satellite box. Just select the channel for cable box or satellite input (ex. CH3) on the unit, then select your desired channel on the cable box or satel- lite box.

ADDING/DELETING CHANNELS

The channels you no longer receive or seldom watch can be deleted from the memory. (Of course, you can add the deleted channel into the memory again.)

1 Select “CHANNEL SET UP”

- TV SETUP -

Hit [SETUP].

B CHANNEL SET UP

Press [K / L] to point to “CHAN-

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

NEL SET UP”, then hit [ENTER].

 

 

 

2 Select “ADD/DELETE CH”

– CHANNEL SET UP –

Press [K / L] to point to

B ADD / DELETE CH (CATV)

“ADD/DELETE CH”, then hit

AUTO CH PROGRAMMING

 

[ENTER].

 

3Enter the desired channel number

Press [CH. K / L] or the Number buttons until your desired channel

number appears. (You can also

08

press [K / L] to enter it.)

ADD / DELETE

You must precede single-digit

 

channel numbers with a zero

(Example: CH8)

(Example: 02 ... 09).

 

When selecting cable channels which are higher than 99, hit [+100] first, then press the last two digits. (Example: to select channel 125, first hit [+100] then hit [2] and [5].)

4Delete (or add) it from (or into) memory

Hit [ENTER]. The channel number changes to light red. The channel is deleted from memory.

To delete another channel, repeat steps 3 to 4.

If you hit [ENTER] again, the channel is memo- rized again.

Added channel : Light blue

Deleted channel : Light red

5Exit the channel setup mode

Hit [SETUP] to exit the menu.

NOTE:

To confirm that channel(s) has been deleted or added, press [CH. K / L].

- 15 -

EN

Image 15
Contents OWNER’S Manual Important Safeguards S2 8 9 8 a RADIO-TV Interference PrecautionsLaser Safety Important Copyright InformationAvoid the Hazards Electrical Shock and Fire Supplied AccessoriesSymbols Used in this Manual LocationwarningTable of Contents TV Mode FeaturesFront Panel Operating Controls and FunctionsRear Panel VHF/UHF Separate Antennas Preparation for USEANTENNA/CABLE Connection VHF/UHF Combined AntennaConnecting to a Stereo Amplifier Equipped with Connecting to Front A/V Input JacksInstalling the Batteries Connecting to a Dolby Digital Decoder for DVDPicture Control TV Operation and SettingsWatching a TV Program DegaussingHit Setup Sleep TimerTo Cancel the Sleep Timer To Cancel the Closed Caption SystemEnter Channel SET UPAuto Channel Programming ADDING/DELETING ChannelsTV-Y7 Chip SET UPChip SET UP TV Rating SET UPPress the Number buttons to enter Mpaa Rating SET UPChange Access Code Menu LanguageCable Channel Designations Unplayable Discs Playable DiscsCalling UP a Menu Screen During Playback Basic Playback General FeaturesDisc Menu Title MenuStep by Step Playback ResumePause Slow Forward Slow ReverseTitle / Chapter Search Marker Setup ScreenSearch Function Track Search Time SearchSpecial Playback Function RepeatprogramRandom Playback Audio Language Changing the SettingsSubtitle Language Stereo Sound Mode Black Level SettingVirtual Surround ON-SCREEN InformationChanging the DVD SET UP Items Language SettingCustom Menu Quick Display SettingAudio Setting When playing disc with copyright ProtectionOther Settings InitializeParental Control Problem Corrective Action Troubleshooting GuideClosed Caption Problem Possible Remedy DVD Mode Servicing MaintenanceCabinet Cleaning Disc HandlingOther Specifications SpecificationsGeneral Specifications Electrical SpecificationsControles DE Operación Y Funciones IndiceTelevisión POR Cable SIN Caja DE CONVERTIDOR/DECODIFICADOR Preparación Para LA UtilizaciónAntena Combinada DE VHF/UHF Antenas Separadas DE VHF/UHFNotas Conexión a UN Decodificador DolbyPara Insertar LAS Pilas Consulte la figura 6 de la páginaPara VER UNA Entrada Externa Para Mirar UN Programa DE TVIdioma DEL Menú Para VER Canales DE Cable O SateliteReproducción Básica Menú DE DiscoReanudación Memo Tel Duration