Sears SRD2900 owner manual Hookups, DVD/VCR to TV Connection, Connecting to a TV

[Back of the DVD/VCR]

SETTING THE CH3/CH4

SWITCH

HOOKUPS

DVD/VCR TO TV CONNECTION

1.	Disconnect the AC power cord of the TV from the			If your TV does not have A/V terminals:
	AC outlet.			When the DVD/VCR COMBINATION UNITS is in the
2.	Disconnect the antenna or cable from the TV.			VCR Playback mode or when the DVD/VCR COMBI-
3.	Connect the antenna or cable to the ANT-IN jack of			NATION UNITS is in the VCR mode, your TV will
	the DVD/VCR COMBINATION UNITS.			receive signals from the DVD/VCR COMBINATION
4.	Connect the DVD/VCR COMBINATION UNITS to			UNITS on either channel 3 or channel 4. To use the
	the TV using the RF cable.			DVD/VCR COMBINATION UNITS with your TV, set
5.	Plug the AC power cords of the DVD/VCR COMBI-			the selector switch to CH3 or CH4 (which is located in
	NATION UNITS and TV into the AC outlets.			the back of your DVD/VCR
	[VHF/UHF	[Indoor antenna]	[Back of the DVD/VCR]	COMBINATION UNITS),
	combination antenna]		[Back of the	whichever is not used for nor-
			UHF/VHF combination TV]				ANT - IN
		OR	RF cable	mal broadcasts in your area.	CH3	CH4
			ANT - IN	Then set your TV to the same			OUT
			(supplied) UHF/VHF
	[Cable	box or satellite box] OR					CH3 CH4
			ANT - OUT	channel.
			CH3 CH4

From Cable or

Satellite Company

Note to CATV system installer

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that pro- vides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the building, as close to the point of cable entry as practical.

CONNECTING TO A TV

			DVD/VCR	COMPONENT
			OUT
Antenna/Cable signal			IN	VIDEO OUT
		ANT - IN	L	DVD/VCR	Y
			AUDO	AUDIO OUT
					Cb S-VIDEO	DIGITAL AUDIO OUT
A/V-compatible or			R	L
					OUT	PCM / BITSTREAM
		ANT - OUT				COAXIAL
wide screen TV		CH3 CH4	VIDEO	R	Cr
	To ANT. IN
	of TV
	To VIDEO INPUT jack		To VIDEO OUT jack			[Fig. 1]
	To Right (red) and Left (white)
Notes	To AUDIO INPUT jacks		To AUDIO OUT jacks

¡Connect the DVD/VCR COMBINATION UNITS directly to a TV. If the A/V cables are connected to a VCR, pictures may be distorted due to the copy protection system.

CONNECTING TO A TV THAT HAS AN

S-VIDEO INPUT JACK OR COMPONENT VIDEO IN JACKS

FOR TVs WITH S-VIDEO INPUT JACK

Use an S-Video cable (commercially available) in place of the yellow video cable to enjoy higher quality pictures.

Note

¡The S-Video connection only supplies video (picture) in the DVD mode of the DVD/VCR COMBINATION UNITS. Therefore, in order to use the VCR features or view TV channels on the DVD/VCR COMBINATION UNITS, you still need to either connect the RF cable to the ANT-OUT jack of the DVD/VCR COMBINATION UNITS and the TV’s Antenna In jack, or connect the yellow video cable as described earlier (Fig.1). To connect the supplied RF cable, see “DVD/VCR TO TV CONNECTION” above.

		DVD/VCR		COMPONENT
		OUT
		IN		VIDEO OUT
	ANT - IN	L		Y
			DVD/VCR
		AUDO	AUDIO OUT
A/V-compatible or		R	L	Cb S-VIDEO	DIGITAL AUDIO OUT
				OUT	PCM / BITSTREAM
wide screen TV	ANT - OUT				COAXIAL
	CH3 CH4	VIDEO	R	Cr
	To Right (red) and Left (white)
	To AUDIO INPUT jacks	To AUDIO OUT jacks			[Fig. 2]
	To S-VIDEO INPUT jack	To S-VIDEO OUT jack
		– 14 –			EN

1L25