Sansui HDLCD5050A owner manual TV operation, To select the video input source

Automatic Search

Start

Signal Type

Cable

E-POP Demo

Off

TV Location

Store

Starting setup

The Auto Setup menu appears the first time you turn on the TV, and assists you to specify the Air/Cable setting, and program your channels automatically.

IMPORTANT: Make sure that the antenna or cable TV system connection is made!

1 To turn on the TV, press POWER. (POWER indicator on the front of the unit changes green. It may take approx. 10 seconds for a picture to appear on screen.) The Auto Setup function begins.

Auto Setup

2	Press ▲ or ▼ to select “TV Location”, then press
	◀ or ▶ to select “Store” or “Home”. This product
	qualifies for ENERGY STAR in Home mode
	default setting.
	NOTE:
	• This unit has been preset to STORE brightness.
	This setting does not qualify under ENERGY
	STAR. To reduce brightness and energy
	consumption, change setting to ‘HOME’. This
	setting does qualify under ENERGY STAR.
	• The device may not conform to the ENERGY
	STAR standard after Reset is performed or the
3	Backlight is adjusted.
	Press ▲ or ▼ to select “E-POP Demo”, then press
	◀ or ▶ to select “On” or “Off”.
	On: A TV feature introduction will pop up at the
	bottom of the screen.
4	Off: Turn off the E-POP Demo feature.
	Press ▲ or ▼ to select “Signal Type”, then press
	◀ or ▶ to select “Cable” or “Air”.

5 Press ▲ or ▼ to select “Automatic Search”, then press ▶ or ENTER.

6 “Auto Setup” will begin. After the Auto Setup is completed, the TV channel appears on the screen.

• Depending on the reception condition, it may take up to 30 minutes to complete memorizing digital cable channels. Please allow the process to complete without interruption.

NOTE:

• If you press EXIT in the process of “Auto Setup”, the Auto Setup stops and changes to the normal screen.

• When you make a menu selection, your changes occur immediately.You do not have to press EXIT to see your changes.

TV operation

1	To turn on the TV, press	POWER.
	(POWER indicator on the front of the unit
	changes green. It may take approx. 10 seconds
	for a picture to appear on screen.)

2 Adjust the volume level by pressing VOL + or – . The volume level will be indicated on the screen by green bars. As the volume level increases, so do the number of bars. If the volume decreases, the number of green bars also decreases.

3 Set the Signal Type option to the appropriate position (see “Air/Cable selection” on page 18).

4 Press the Direct Channel Selection (0-9, –) buttons to select the channel.

(If you press only channel number, channel selection will be delayed for a few seconds.)

TO SELECT ANALOG CHANNELS

1-9: Press 1-9 as needed. Example, to select channel 2, press 2, then press

ENTER.

10-99: Press the 2 digits in order. Example, to select channel 12, press 1, 2, then press ENTER.

100-135: Press the 3 digits in order. Example, to select channel 120, press 1, 2, 0, then press ENTER.

TO SELECT DIGITAL CHANNELS

Press the first 1-3 digits, then press the – button, followed by the remaining number.

Example, to select channel 15-1, press 1, 5, –, 1, then press ENTER.

• If a channel is selected with only audio content, “Audio only” will be displayed on the screen.

• If a channel is selected with a weak digital signal, “Digital channel signal strength is low” will be displayed on the screen.

The same program may be available on either an analog channel or a digital channel.You may choose to watch either format.

• If a channel is selected to which you have not subscribed, “Digital channel is encrypted” will be displayed on the screen.

VHF/UHF/CABLE CHANNELS

Air		Cable
VHF		VHF
2-13		2-13
UHF	STD/HRC/IRC
14-69	14-36	(A) (W)
	37-59	(AA) (WW)
	60-85	(AAA) (ZZZ)
	86-94	(86) (94)
	95-99	(A-5) (A-1)
	100-135 (100) (135)
	01	(4A)

NOTE:

• If a channel with no broadcast is selected, the sound will automatically be muted.

• It may take a few seconds for a digital channel picture to appear on screen after being selected.

To select the video input source

To view a signal from another device connected to your LCD TV, such as a VCR player, press INPUT SELECT, then press ▲ or ▼ or corresponding Number buttons (0-7), then press ENTER.

Input Select

0.TV

1.Video1

2.Video2

3.Component

4.HDMI1

5.HDMI2

6.HDMI3

7.PC

[0-7]:Select

15EN