Sansui HDLCD185W owner manual Starting setup, TV operation, To select the video input source

Page 15

Starting setup

The Auto Setup menu appears the first time you turn on the TV, and assists you to specify the Air/Cable setting, and program your channels automatically.

IMPORTANT: Make sure that the antenna or cable TV system connection is made!

1 To turn on the TV, press (POWER) (It may take approx. 10 seconds for a picture to appear on screen.). The Auto Setup function begins.

Auto Setup

 

TV Location

Store

 

 

E-POP Demo

On

 

 

Signal Type

Cable

 

 

Automatic Search

Start

 

2

Press ▲ or ▼ to select “TV Location”, then press

or to select “Home” or “Store”. This product

 

qualifies for ENERGY STAR In Home mode

 

default setting.

 

NOTE:

 

• This unit has been preset to STORE brightness.

 

This setting does not qualify under ENERGY

 

STAR. To reduce brightness and energy

 

consumption, change setting to ‘HOME’. This

 

setting does qualify under ENERGY STAR.

 

• The device may not conform to the ENERGY

 

STAR standard after Reset is performed or the

3

Backlight is adjusted.

Press ▲ or ▼ to select “E-POP Demo”, then press

or to select “On” or “Off”.

 

On: A TV feature introduction will be popped up

 

at the bottom of the screen.

4

Off: Turn off the E-POP Demo feature.

Press ▲ or ▼ to select “Signal Type”, then press

or to select “Air” or “Cable”.

5 Press ▲ or ▼ to select “Automatic Search”, then press or ENTER.

6 “Auto Setup” will begin. After the Auto Setup is completed, the TV channel appears on the screen.

• Depending on the reception condition, it may take up to 30 minutes to complete memorizing digital cable channels. Please allow the process to complete without interruption.

NOTE:

• If you press EXIT in the process of “Auto Setup”, the Auto Setup stops and changes to the normal screen.

• When you make a menu selection, your changes occur immediately.You do not have to press EXIT to see your changes.

TV operation

1

To turn on the TV, press

 

(POWER).

 

 

(It may take approx. 10 seconds for a picture to

2

appear on screen.)

Adjust the volume level by pressing VOL + or .

The volume level will be indicated on the screen

 

by green bars. As the volume level increases, so

 

do the number of bars. If the volume decreases,

 

the number of green bars also decreases.

3 Set the Signal Type option to the appropriate position (see “Air/Cable selection” on page 18).

4 Press the Direct Channel Selection (0-9, –) buttons to select the channel.

(If you press only channel number, channel selection will be delayed for a few seconds.)

TO SELECT ANALOG CHANNELS

1-9: Press 1-9 as needed. Example, to select channel 2, press 2, then press

ENTER.

10-99: Press the 2 digits in order. Example, to select channel 12, press 1, 2, then press ENTER.

100-135: Press the 3 digits in order. Example, to select channel 120, press 1, 2, 0, then press ENTER.

TO SELECT DIGITAL CHANNELS

Press the first 1-3 digits, then press the button, followed by the remaining number.

Example, to select channel 15-1, press 1, 5, , 1, then press ENTER.

• If a channel is selected with only audio content, “Audio only” will be displayed on the screen.

• If a channel is selected with a weak digital signal, “Digital channel signal strength is low” will be displayed on the screen.

The same program may be available on either an analog channel or a digital channel.You may choose to watch either format.

• If a channel is selected to which you have not subscribed, “Digital channel is encrypted” will be displayed on the screen.

VHF/UHF/CABLE CHANNELS

Air

 

Cable

VHF

 

VHF

2-13

 

2-13

UHF

STD/HRC/IRC

14-69

14-36

(A) (W)

 

37-59

(AA) (WW)

 

60-85

(AAA) (ZZZ)

 

86-94

(86) (94)

 

95-99

(A-5) (A-1)

 

100-135 (100) (135)

 

01

(4A)

NOTE:

• If a channel with no broadcast is selected, the sound will automatically be muted.

• It may take a few seconds for a digital channel picture to appear on screen after being selected.

To select the video input source

To view a signal from another device connected to your TV, such as a VCR player, press INPUT SELECT, then press ▲ or ▼ or corresponding Number buttons (0-4), then press ENTER.You can select TV, Video, Component, HDMI or PC depending on which input jacks you used to connect your devices.

Input Select

0.TV

1.Video

2.Component

3.HDMI

4.PC

[0-4]:Select

15

Image 15
Contents Orion Website HDLCD185WEnglish Charges, of the National Wire to an antenna discharge unit, sizeTo provide some protection against Voltage surges and built-up staticThis Manufacturer Cares Child SafetyIssue Tune Into SafetyCondensation HOW to Handle the LCD PanelHow to remove the stand How to attach the standFeatures Power sourceTo USE AC Power Contents Parts and functions Front Right sideRear Battery Precautions Remote controlCable TV connections Antenna connectionsVCR Connections to other equipmentTo connect the unit to a VCR To connect the unit to a camcorder, or a game consoleUsing an AV Amplifier with built-in digital surround To connect the unit to a PC Personal ComputerTo PC/DVI Audio Audio cord not supplied To Hdmi To connect a Hdmi or a DVI device to the unit Rear of the unit To PC/DVI AudioDVI device Hdmi device Starting setup TV operationTo select the video input source Press MENU. The TV menu screen will appear Quick guide for menu operationChannel number Station name Channel numberConvenience functions Icon Selected Items Setup hintAdding Channel Memorizing channelsAir/Cable selection Automatic SearchTo create channel labels Labeling channelsTo set the V-Chip Setting the V-ChipTo register a password To change the passwordTo clear the all V-Chip settings Closed CaptionCC advanced Setting the picture size Ignition Reception disturbancesBlock Noise / Picture Freeze TroubleshootingSpecifications AccessoriesGeneral 3471 N. Union DR Orion SALES, INCMemo J3EZ0601A SH 11/07 N