Panasonic DMR-E80H operating instructions Press 3, 4 to select Antenna Sys Tem and press Enter

Press [ENTER] to complete Plug-in Auto Tuning.

If the unit couldn’t set the clock automatically

Press [ENTER] to show the “Manual Clock Setting” screen. Set the time manually (➜ page 47).

To start Plug-in Auto Tuning again (after reloca- tion, for example)

Antenna system, channel caption, and VCR Plusr guide channel settings all revert to the default values when you perform the procedure below. Timer recording settings are also cleared.

When the unit is on and stopped

1 Press and hold [X, CH] and [W, CH] on the main unit for about five seconds.

The unit turns off.

2 Press [Í, DVD POWER] to turn the unit on. Follow the above steps 2–4.

If Plug-in Auto Tuning fails

When the display shows the correct time

4

Press [ENTER].

Plug-in Auto Tuning starts and the unit puts the stations it can receive into channels.

The unit then proceeds with Auto Clock Setting. The time is displayed when finished. If the clock is an hour slower or faster than the actual time, go to “Time Zone Adjust” to cor- rect it (➜ page 47).

3

Connect antenna cable and if you use a cable box, tune it to your local PBS CH then. . .

Please push the ENTER key.

ENTER RETURN

English

Auto Channel/Clock Setting

e.g., when you select

lan-

English

Español

Français

Press ENTER

Pulse ENTER

Appuyer sur ENTER

2 Press [3, 4] to select the menu guage and press [ENTER].

Select Language

Seleccione la Lengua Sélection de Langue

turn the

Press [Í, DVD POWER] to unit on.

1

video input to

Preparation

≥Confirm that the antenna is connected correctly. ≥Turn on the television and select the appropriate

suit the connections to this unit.

1 Press [SETUP] to show the menus.

SETUP	Antenna System	CATV
	Auto Channel Setting
Channel	Channel Caption
	Preset Channel Caption
Set Up
	Manual Channel Caption
Disc
Video	VCR PlusiCH Setting
Audio
Display	TAB SELECT
TV Screen	RETURN

2 Press [3, 4] to select “Channel” and press [1].

SETUP	Antenna System CATV
	Auto Channel Setting
Channel	Channel Caption
	Preset Channel Caption
Set Up
	Manual Channel Caption
Disc
3 Press [3, 4] to select “Antenna Sys-		up
tem” and press [ENTER].
		Setting
SETUP	Antenna System
	TV
Channel	CATV
Set Up

4 Press [3, 4] to select “TV” or “CATV” and press [ENTER].

The screen shown in step 2 reappears.

5 Press [3, 4] to select “Auto Channel

Setting” and press [ENTER].

SETUP	Auto Channel Setting
Channel	Connect antenna cable and if you use a
	cable box, tune it to your local PBS CH
Set Up	then...
Disc	Please push the ENTER key.
Video
Audio
Display

If you have not yet set clock, the “Auto Channel/Clock Set- ting” screen appears.

6 Press [ENTER].

Auto setting starts. This takes a few minutes. (To stop auto channel setting, press [RETURN].) When finished, the Com- plete screen or time display is shown. Press [ENTER].

To return to the previous screen

Press [RETURN].

When you are finished

Press [SETUP].

Adding and deleting channels

Add or delete channels if necessary channels are not set or unnec- essary channels are set.

While this unit is receiving the antenna signal (but not during recording):

1 Press the numbered buttons to select a channel.

e.g.,	“5”:	[0] ➜	[5]	Unit’s display
	“15”:	[1] ➜	[5]
	“115”:	[100]➜ [1] ➜ [5]

≥You can also use [W, X, CH] when you are going to delete a channel.

2 Press [ADD/DLT].

The channel is deleted if it was set or added if it was not set. e.g.,

CHANNEL 15 DELETED

Repeat steps 1 and 2 as necessary.

7

RQT6984