Text.fm Page 21 Tuesday, April 27, 2004 8:21 AM
|
|
|
| Additional information | |
| Specifications |
|
|
|
|
|
|
|
|
| |
| Transmission standards |
|
| ||
|
|
|
|
| |
| Channel coverage | UHF channels B21 - B69 |
|
| |
|
|
|
| ||
| TV scart | 21 pin Euro connector (CENELEC standard) with SMARTLINK support | |||
|
|
|
| ||
| VCR scart | 21 pin Euro connector (CENELEC standard) with SMARTLINK support | |||
|
| and synchro record |
|
| |
|
|
|
| ||
| Audio output socket | Digital optical output (PCM using a mini TOS lead) or analogue | |||
|
| (2V RMS), 3.5mm jack socket |
|
| |
|
|
|
|
| |
| Supply voltage | 220 ~ 240V AC, 50Hz |
|
| |
|
|
|
|
| |
| Power consumption | 10W (Maximum) |
|
| |
|
|
|
|
| |
| Operating temperature |
|
| ||
|
|
|
|
| |
| Dimensions (W x H x D) | 215 x 48 x 240mm |
|
| |
|
|
|
|
| |
| Weight | 1.5 Kg Approx. |
|
| |
|
|
|
| ||
| Accessories supplied | 1 Remote control | |||
|
| batteries, 1 Receiver stand,1 fully wired Scart lead | |||
|
|
|
|
| |
| Design and specifications are subject to change without notice |
| |||
| Troubleshooting |
|
|
|
|
|
|
|
| ||
| Problem | Possible cause | Solution | ||
|
|
|
|
|
|
| The indicating light on the | • | Mains cable not connected | • | Plug mains cable into power socket |
| front panel is not illuminated |
|
|
|
|
|
|
|
|
| |
| The indicating light is Red | • The receiver is in standby | • | Press the l/1 button on the remote | |
|
|
| mode |
| control to cancel standby mode |
|
|
|
|
|
|
| Remote control not working | • | Batteries low | • | Replace both batteries |
|
|
|
|
| |
| You cannot find a channel | • The channel only broadcasts | • | Check the programme listings | |
| you have previously watched |
| for part of the day |
|
|
|
|
|
|
|
|
| No picture | • | Scart plug loose | • | Check scart plugs are firmly |
|
|
|
|
| connected |
|
| • Your TV might be unable to | • | Set the TV to AV mode e.g AV1 or | |
|
|
| switch automatically into the |
| EXT1 etc. (refer to your TV |
|
|
| AV mode |
| manual) |
|
|
|
|
| |
| Picture freeze | • | Receiver malfunction | • Press and hold down the l/1 | |
|
|
|
|
| button on the front panel for 5 |
|
|
|
|
| seconds then release and wait until |
|
|
|
|
| indicating light turns red. Press the |
|
|
|
|
| l/1 button on the remote control to |
|
|
|
|
| resume normal operation |
|
|
|
|
|
|
| Picture and sound break up | • | Signal strength low (see page | • | Check aerial installation |
|
|
| 14) |
|
|
|
|
|
|
|
|
| No sound | • | Volume set too low on the TV | • | Increase volume setting of your TV |
|
| • | TV in Mute mode | • | Cancel Mute mode |
|
| • | Scart plug loose | • | Check scart plug connection |
|
|
|
|
|
|
Attention:
Picture distortion may occur if this unit is positioned in close proximity to any equipment emitting electromagnetic radiation.
®
Additional information
21