Sylvania lc320ss8 5Sound Adjustment, You can adjust treble, bass and surround, Treble, Bass

Page 25

5Sound Adjustment

You can adjust treble, bass and surround.

1Press [SETUP] to display the main menu.

2Use [Cursor K/L] to select “SOUND”, then press [ENTER].

3Use [Cursor K/L] to select the sound type you want to adjust, then press [ENTER].

Sound

Treble		0
Bass		0
Surround
Surround		Off
Reset Settings

	Surround		INTRODUCTION
	Surround
	Use [Cursor K/L] to turn on or off the surround
	function, then press [ENTER].
	Sound		CONNECTION
	Treble		CONNECTION
	Bass
	Surround	On
	Reset Settings	Off
	Reset Settings		INITIAL
	Use [Cursor K/L] to select “Reset”, then press [ENTER]		INITIAL
	Use [Cursor K/L] to select “Reset”, then press [ENTER]
	to restore the “Sound” settings to default.		SETTING
	Reset Settingsi		SETTING
	This function resets the Sound	Cancel
	settings to factory default.	Reset
		Reset
			WATCHING TV

Note:

• To cancel sound adjustment, press [SETUP].

5 Press [SETUP] to exit.OPTIONAL SETTING

4Adjust the sound setting.

Treble, Bass

Use [Cursor s/B] to adjust.

				Cursor s	Cursor B
Treble				to decrease	to increase
Treble	0			higher-pitched	higher-pitched
Adjust		Move	ENTER Enter	sounds	sounds
Adjust		Move	ENTER Enter
Bass				to decrease	to increase
				to decrease	to increase
Bass	0			lower-pitched	lower-pitched
Adjust		Move	ENTER Enter	sounds	sounds

TROUBLESHOOTING INFORMATION

25

EN

Image 25

Contents LC320SS8 To Receive DIGITAL/ANALOG SIGNAL, YOU Must Connect AntennaImportant note is located on the rear of the cabinet IntroductionRADIO-TV Interference Precautions5Symbols Used in this Manual 5Supplied AccessoriesQuick start guide Remote control LocationContents FeaturesDTV/TV/CATV 5Installing the Batteries 5Remote Control Function5Control Panel 5Basic Connection ConnectionAntenna Cable Connection Connection to Cable Box or Satellite BoxHdmi Connection 5External Device ConnectionHDMI-DVI Connection Video Cable Connection Component Video Cable ConnectionAudio Output Connection Digital Video ConnectionAnalog PC Connection 5Initial Setup Initial SettingMake sure if the unit is connected to antenna or cable Scanning and memorizing of channels start automatically5Auto Channel Scan 5Main MenuEnter 5Language SelectionWhat is the minor channel? 5Volume AdjustmentWatching TV 5Channel Selection5Switching Each Mode 5Still ModeYou can freeze the image shown on the TV screen This section describes how to switch the audio language 5Switching Audio ModeStereo SAPPress Info 5Screen InformationBroadcasting Information Day of Memories5TV Screen Display Mode Press Sleep to set the sleep timer 5Sleep TimerTo Cancel the Sleep Timer 5Channel List Optional SettingChannel l List 5Antenna Confirmation 5Manual RegisterUse Cursor K/L to select Manual Register, then press Enter Use Cursor K/L to select Antenna, then press Enter5Picture Adjustment You can adjust treble, bass and surround 5Sound AdjustmentAdjust the sound setting Treble, BassClosed Caption DTV CC 5DTV Closed CaptionUse Cursor K/L to select DTV CC, then press Enter DetaililFont Style 5CC StyleClosed Captioning font style can be changed as below Font SizeFont Opacity Font ColorBack Color Back OpacityChipip Enter password New Password DpageChip Mpaa RatingDpage TV RatingDpageAssociation of America Then press Enter repeatedly to switch betweenUse Cursor K/L to select TV Rating, then press Block View and BlockChipip Enter password Confirm password Use Cursor K/L to select New Password, then press EnterTV-14 Category RatingClock, Phase 5PC SettingsHorizontal Position, Vertical Position Cursor sAudio 5HDMI Audio5Troubleshooting Guide TroubleshootingRefer to IR Signal Check on Check the batteries of the remote controlDelayed behind the dialogue Entered channel numberInformation MaintenanceGlossary Atsc5Electrical Specification 5General Specifications5Other Specifications 5Cable Channel DesignationsMemo Limited Warranty