JVC AV-T2122 manual T T I N G S T a R T E D, Power

Page 7

G E T T I N G S T A R T E D 7

POWER

Press the Power button ( ) on the TV front panel. The Power lamp will light red.

If the TV will not be turned on even if you press the POWER button, the TV is in the stand-by mode. Press the POWER button on the remote control to turn on the TV.

To turn the power off, press the POWER button on the remote control. The Power lamp will light red.

The On Timer lamp will light when the On/Off Timer is set, even when the TV power is off.

When you do not use the television for a long period of time, turn the power off by pressing the

Power button ( ) on the TV front panel. The Power lamp will go out.

There are two methods to turn the power on after turning it off by pressing the POWER button on the remote control or by using the On/Off Timer function:

1)Press the POWER button on the remote control.

2)Press the CHANNEL button and CHANNEL button on the TV front panel at the same time.

When the On-Timer function is set, the On-Timer lamp will light. Even if you turn the power off by pressing the POWER button on the remote control, if the On-Timer function is active the On- Timer lamp stays lit. See page 12 to set On/Off Timer.

ADJUSTING VOLUME

1

Press the VOLUME button on the front panel or remote control. The volume level bar will ap- pear.

VOLUME 13

- - - - - - - - - - - - - - - - - - -

2

Press the MUTING button to instantly turn the volume off to zero. To restore the volume to your previous level, simply press the MUTING button again.

CHANGING CHANNELS

1

10 key direct access.

Press the numbers on the remote’s 10 key pad. For single-digit channel numbers press 0 then the number. For channels above 100, press the 100+ button plus the 2-digit number.

2

CHANNEL button.

Press the CHANNEL button, it will scan the channels in order.

NOTE: After you operate the Auto Tuner Setup (page 9), all of the blank or empty, channels will be removed from scanning so that there is no noise or channel snow when you scan, only active channels.

3

Return.

Press the release of the RETURN+ button to return to the previous channel. First, select a channel (game #1). Then, select another channel (game #2) with the 10 key pad and push the RETURN+ button to flip directly back and forth.

4

Return+.

Press and hold down the RETURN+ button for three seconds. The message, “RETURN CHANNEL

PROGRAMMED !” will appear and you can scan as you wish with the CHANNEL button. Press RETURN+ again and you will go back to the Return+ channel you programmed.

To cancel the Return+ channel, press and hold down the RETURN+ button for another three sec- onds and the message, “RETURN CHANNEL CANCELED !” appears.

Pressing any number key or turning the TV off will also cancel a Return+ channel.

Image 7
Contents AV-T2122 Getting Started N N E C T I O N S O N N E C T I O N S Connecting the Antenna and VCRVCR for playing Changing the Batteries E T T I N G S T a R T E DBe sure to use only size AA/R6/UM-3 batteries T T I N G S T a R T E D PowerS I N G T H E M E N U Using this GuideI T I a L S E T U P I C T U R E S E T T I N G S Balance U N D S E T T I N G SBass TrebleClock SET Message ON/OFF TimerE N E R a L I T E M S SET ClockADD N E R a L I T E M SChannel Summary Channel Guard LockPadlock icon appears SET Lock Code Child LockVideo Status Sleep TimerT T O N F U N C T I O N S DisplayU T T O N F U N C T I O N S Scan with Channel You can select the sharpness of picture when receiving RFRETURN+ Picture BoosterTroubleshooting Model Specification SAV-T2122