Sylvania DVL515 Setup Connections, Connection to a TV, After you have completed connections

Setup

Connections

If your TV has AUDIO/VIDEO input jacks, see the following instructions.

Connection to a TV

Basic Audio

TV	LR
	AUDIO IN

(INPUT)

Audio cable (supplied)

This unit

(OUTPUT)

Setup	AUDIO VIDEOCOMPONENTS-VIDEO OUT OUTVIDEOOUTOUT		COAXIAL	DIGITAL AUDIO OUT	YC/P	OUT		L
		R	C/P				R
					L
							AUDIO

(Analog)

AUDIO OUT

Hint

Method 1	Method 2
Good picture	Better picture
VIDEO IN	S-VIDEO IN

	or	S-Video
Video		cable
cable		(commercially
(supplied)		available)

VIDEO OUT S-VIDEO OUT

VIDEO OUT S-VIDEO OUT

Method 3

Best picture

COMPONENT

VIDEO IN

YY

PBCB

or

PRCR

Component Video cables (commercially available)

COMPONENT VIDEO OUT CB/PB Y CR/PR

COMPONENT VIDEO OUT

•Connect this unit directly to the TV. If the Audio/Video cables are connected to a VCR, pictures may be distorted due to the copy protection system.

•When progressive scanning mode is selected, no video signal will be output from the VIDEO OUT or S-VIDEO OUT jack.

If your TV is compatible with 525p (480p) progressive scanning and you want to enjoy that high quality picture;

You must select the connection Method 3 above and progressive scanning mode. To set the mode, press and hold [PLAY B] on the front panel for more than 5 seconds, so that PROGRESSIVE indica- tor will light up.

If your TV is not compatible with progressive scanning;

Use this unit in interlace mode. Make sure that PROGRESSIVE indicator is off. If not, press and hold [PLAY B] on this unit for more than 5 seconds, so that PROGRESSIVE indicator of this unit will light off.

[This unit]

C STOP

B PLAY

EJECT

more than 5 seconds [Interlace mode]

[Progressive scanning mode]

After you have completed connections

•Hit the input selector button (usually TV/VIDEO, INPUT or AUX) on your TV to switch an appropriate external input channel (usually near channel 0) for viewing the picture from this unit. If the picture does not appear, also refer to the manual accompanying your TV.

INPUT MODES FOR COMMON TV BRANDS (Example)

• Listed below are inputs for common brand name TV’s.

Admiral:	AUX
Curtis Mathis:	LINE1, LINE2, 00, 90, 91, 92, 93
GE:	INPUT, TV/VCR, 00, 90, 91, 92, 93
Hitachi:	INPUT, AUX
JVC:	A/V CHANNEL, INPUT1, SVIDEO, INPUT2
Kenwood:	AUX
LXI-Series:	00
Magnavox:	AUX CHANNEL

Panasonic:	TV/VIDEO
RCA:	INPUT, TV/VCR, 00, 90, 91, 92, 93
Samsung:	TV/VIDEO
Sanyo:	VIDEO
Sharp:	00
Sony:	VIDEO1, VIDEO2, VIDEO3
Toshiba:	TV/GAME
Zenith:	00

RF Modulator Connection

If your TV has Antenna in jack only, it is still possible to connect this unit to your TV by using a STEREO AUDIO/VIDEO RF Modulator (commercially available).

In this case, follow the instructions below.

1)Connect the AUDIO/VIDEO output jacks of this unit to the AUDIO/VIDEO input jacks of your RF Modulator by audio and video cables.

2)The antenna input jack of your TV may have been already occupied. If so, disconnect the RF cable from your TV, and then connect the RF cable to your RF Modulator (usually marked “ANT IN”).

3)Connect your RF modulator to your TV by another RF cable.

4)Set your RF modulator’s channel 3/4 switch to either 3 or 4, whichever the TV channel is least used in your area. If your RF modulator has a Modulator/Antenna switch, set it according to your RF modulator’s manual.

5)Turn on your TV and choose the same channel as you set the RF modulator’s channel 3/4 switch to.For more details, follow the instructions supplied with the RF Modulator.

Cable Antenna	(Back of this unit)
Signal				(Back of TV)
Stereo Audio/Video RF Modulator	R	COAXIAL	DIGITAL AUDIO OUT	L

	3	4			R	L	1	OUT OUTVIDEOOUT	AUDIO VIDEOCOMPONENTS-	C/P	YC/P
(commercially available)
AC 120V ANT IN	CHANNEL		TO TV	VIDEO	AUDIO
							Audio/Video	OUT	VIDEO
							Cables
							(Supplied)
2				3		RF Cable (Not supplied)
											Antenna in jack

Hint

•The quality of picture may become poor if the unit is con- nected to an RF Modulator.

– 6 – EN