ProScan 32LC30S60 user manual Troubleshooting, Possible Solutions

Page 23

Appendix

Troubleshooting

Before calling a service technician, please check the following table for a possible cause of the problem and some solutions.

Customer important notice: If the TV functions cannot be operated, unplug the AC cord from AC power source, wait at least 1 minute, then re=plug AC cord. This will reset the TV settings and should restore TV to normal operation.

 

Symptoms

 

 

 

 

 

 

 

 

Possible

Solutions

 

 

 

 

 

 

 

 

 

 

[]

Make

sure

the

power

cord

is plugged in,

then

press

Power.

 

 

 

 

 

 

[]

The

remote

control

batteries

may

be dead.

Replace

the

batteries.

TV will

not

turn

on

[]

Unplug the

VGA wire

and plug

 

the

power

wire

again.

 

 

 

 

 

 

 

 

[]

Plug

another electrical

device

 

into

AC outlet

 

to confirm

the

outlet is

 

 

 

 

 

working

 

properly.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[]

Check if you have set

the

timer

off.

 

 

 

 

 

 

 

No

picture,

no sound

[]

Check

the

antenna/cable

connections.

 

 

 

 

 

 

 

 

 

 

 

 

-

Press

[Display]

to

see if you

have selected

the

right

signal

source.

 

 

 

 

 

[]

The

sound

may

be muted.

Press [VOL+

] on

the

remote

control.

No

sound,

picture

OK

[]

The

station

may have

broadcast

difficulties.

 

Try

another

channel.

[]

Check

the

speakers

cable

connections.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

,

Make

sure

headphones

are not

connected.

 

 

 

 

 

 

Poor sound, picture OK

[] The station may have broadcast difficulties. Try another channel

[] Check the speakers cable connections.

[] Check the antenna connections.

Poor picture, sound OK

[] The station may have broadcast difficulties. Try another channel. , Adjust the picture from the menu.

Unable to select a certain channel

Poor color or no color

The remote control does not operate

[] The channel may be skipped. Choose this channel by directly selecting the buttons from the remote control.

[] The station may have broadcast difficulties. Try another channel.

[] Adjust Saturation in the Video settings menu.

[] There may be an obstruction between the remote control and the remote control sensor.

[] The batteries may be installed with a wrong polarity.

[] The remote control batteries may be dead. Replace the batteries.

[]

This may be caused because of a very short interval between POWER

Disorder display at power on

OFF and ON.

-

Unplug the power and restart.

22

Image 23
Contents Usersman UAL Federal Communications Commission Statement Contents Important safety instructions Important safety instructions Base instalation instruction Preparation for using your new TVLearning about your TV View the front connection panelView the back connection panel Selecting a location for the TV Connection to other devices Side panel connectionBack panel connection Preparation for using your new TVConnecting component devices DVD/DVR Connecting your TV Connecting to an antennaConnecting Cable/Satellite and A/V Equipment Service jackConnecting Audio Connecting ComputerConnecting to a cable converter box Connecting HdmiFor subscribers to Scrambled Cable IV Service For subscribers to Basic Cable TV ServiceInstaling the remote control batteries Preparing the remote control for useUsing the remete control Menu operation Signal source selectionTV Settings Power ON/OFFSelect screen modes Select sound modesUse Hute button Select picture modesSelect channels by numbers Adjust VolumeAudio mode adjustment Video mode adjustmentBasic operation SetupAll children Program Block = A. Rating Enable is onParental Control About Canada About Hpaa RatingAbout Canada English PG=13 ParentsTo clean the TV screen Cleanin and CarePossible Solutions TroubleshootingWall-mounting Bracket Installation Appendix Resolution