| Problems |
| Solutions |
| TV’S UNIVERSAL |
| This television follows SONY’s universal remote code. To find |
| REMOTE CODE |
| the actual code you must read through your own universal |
|
|
| remote’s guide book. |
| TV CHANNELS ARE |
| Check your auto lock function’s settings inside the OSD. You |
| BLOCKED |
| may have locked up some channels but forgot about them. |
|
|
| Refer to page 32 for more instructions. |
| UNIVERSAL |
| This TV follows SONY’s universal remote code. Please check |
| REMOTE CODE |
| your hand book for SONY’s codes then apply them. |
| THE TV TURNS ON |
| This TV is a High Definition liquid crystal display panel TV. It |
| OR OFF SLOWLY |
| requires a few more seconds than normal TVs to power up and |
| AND THE SCREEN |
| show the picture. |
| SHOWS UP |
|
|
| SLOWLY |
|
|
| NO SOUND ON PC |
| Make sure you have a 3.5 mm |
|
|
| your pc’s sound output to the TV’s VGA STEREO INPUT. |
| HDCP VIDEO SAYS |
| Reboot your HDCP video device but turning them off and |
| NO HDCP SUPPORT | unplugging the power cord. Wait up to 8 minutes to plug the | |
|
|
| power back in to see if it works or not. |
|
|
| Make sure you have a 3.5 mm |
| HDCP VIDEO HAS |
| your HDCP video device’s sound output to the TV’s VGA |
| NO AUDIO |
| STEREO INPUT. If your HDCP video device uses RCA AUDIO |
|
|
| jacks, you’ll need to obtain a RCA audio converted into 3.5 mm |
|
|
| |
| CANNOT GET |
| Make sure the TV is recognized as plug and play monitor. Try |
| 1360X768 ON PC |
| updating your video card’s drivers as well. If that does not help, |
| VGA |
| most likely you’ll need to upgrade your video card to a newer |
|
|
| one. |
| PICTURE IS |
| This might be from interference from large electrical appliances, |
| DISTORTED OR |
| cars, motorcycles, or fluorescent lights. If the TV is close to the |
| HAS ABNORMAL |
| wall, try moving the TV to another room in your house to see if |
| SOUND |
| the problem still occurs. |
|
|
| If you’re using HDMI or a TV digital channel make sure you use |
|
|
| the ASPECT button to switch to 16:9 format. If you are using |
|
|
| VGA, use the AUTO ADJUST function to adjust to the screen. |
| PICTURE DOES |
| Please Note : If you are using regular analog TV, AV, or |
|
| component in 480i resolution, use the ASPECT button to switch | |
| NOT COVER THE |
| to 16:9 in order to fill up the screen. Please Note : This note |
| ENTIRE SCREEN |
| this feature will distort the picture. |
|
|
| For best image quality, view HD widescreen programs where |
|
|
| possible. If HD content is not available view “Standard |
| PICTURE QUALITY |
| Definition” from a digital source. Standard, analog TV will |
|
| always be noticeable inferior to HD because your TV has video | |
| IS HORRIBLE!! |
| |
|
| that is many times better than old TV’s and so you can see | |
|
|
| |
|
|
| interference and deficiencies you did not KNOW you had. |
| PICTURE HAS |
| Your TV is manufactured using an extremely high level of |
| PIXELS THAT ARE |
| precision technology, however, sometimes some pixels of your |
| ALWAYS |
| TV may not display. Pixels defects within industry specifications |
| DISPLAYING THE |
| are inherent to this type of product and do not constitute a |
| SAME COLOR |
| defective product. |
- 44 -
www.SCEPTRE.com
QUASAR SQ3200* User Manual