Sceptre Technologies X460 user manual Switching a

Page 46

Problems

Solutions

SWITCHING A

Different channels and inputs will sometimes have this effect

CHANNEL OR

because the channel signal’s own volume is already loud.

SOURCE CHANGES

There is no way remove this completely. The TV has an

THE VOLUME

AUTO VOLUME LEVEL function that can combat this type of

 

effect. Please make sure that function is turned on.

THERE IS NOISE OR

When your TV’s resolution is higher than the digital channel’s

TRASH PIXELS ON

broadcast resolution, the signal is up-converted to match your

THE SCREEN

TV’s resolution. Up-converting can cause this type of effect.

TIPS FOR HIGH

The TV is an ideal platform for viewing High Definition

DEFINITION USERS

Content. The best image quality can be achieved by HDMI,

 

YPbPr (Component), then VGA. However, due to variances in

 

broadcast practices, it is possible some image distortions can

 

occur.

TIPS FOR

Letterboxed (Widescreen) versions of DVD movies are most

LETTERBOX

commonly formatted for standard 4:3 TVs. The TV has the

CONTENT USERS

capability of expanding this content so the entire screen is

 

filled at the expense of the image proportion. To use this

 

function press the aspect button on the remote control and

 

cycle among the available options.

I CANNOT FIND THE

The buttons are represented by the ▲▼◄► buttons located

VOLUME AND

on the remote control. ▲▼ changes the channels and ◄►

CHANNEL

changes the volume.

CHANGING

 

BUTTONS

 

TV TURNS OFF

The TV features a power saving mode which will automatically

AUTOMATICALLY

turn off the TV, if there’s no signal provided for more than 5

AFTER 5 MINUTE

minutes.

 

 

TV TURNS OFF

The TV features an option to turn the TV off after 3 hours of no

AUTOMATICALLY

operation (meaning you did not use the remote for 3+ hours).

AFTER 3 HOURS

Please check the MENU to make sure that option is not

 

toggled.

 

 

MY TV PICTURE IS

Check to see if you are under POWER SAVING mode for your

VERY DIM

picture mode. Keep pressing the PICTURE button on the

 

remote control to cycle out of POWER SAVING.

 

 

- 46 -

www.SCEPTRE.com

SCEPTRE X460 HDTV User Manual

Image 46
Contents Dear Sceptre Customer Important Information Safety Instructions Safety Instructions Page Television Antenna Connection Protection External Television Antenna GroundingInstallation Package ContentsOpening the Package Removing the Stand Table of Contents Front View Identifying Front and Rear PanelRear View Mounting Pattern Side Control Buttons Rear View Connections Please NoteSceptre X460 Remote Control Installing Batteries to the Remote Control Connection Suggestions If You Have Digital Cable without Cable Box or Antenna…Connecting DVD Player with Component YPbPr… Connecting Wii with Composite… Connecting Cable or Satellite boxes with HDMI… Connecting to a PC with VGA and 3.5 mm minijack … Connecting a Digital Audio Receiver with Coax SPDIF… Switching Sources Starting up the Hdtv Ready to Watch Some TV?If You’ve Connected Antenna or Cable to the TV… Page OSD On Screen Display Controls Via Remote ControlVia TV Side Panel Buttons OSD On Screen Display Options PictureUnder PC VGA there are only full and dot by dot mode Advance Picture Settings Sound Other Settings AVL Under Other Settings Channel III. Channel Setting Parental Setup III. Clock Others Detailed Explanations USB Connection ExplainedMedia Setting Closed Captioning digital and analog Explained Rating ExplainedMpaa Aspect Ratio Explained NormalShortcuts to Browsing Channels To ADD to the Favorite ListHow do I clean the TV ? Cleaning the bezel and remote controlTroubleshooting Problems SolutionsTV Channels are Switching a Call Us If You Need Help Specification Illustration4NTSC/ATSC Limited Product Warranty Warranty Service Disclaimer, Trademarks, & Copyright Information FCC Compliance Statement European Notice