New Transducers 42PF9830/93 Menu preferences, Programme title, Set/Change code, Factory settings

Page 12

Settings/Setup

Preferences

Menu preferences

Picture/sound preferences

OSD

Features preferences

Programme title

Menu preferences

Set/Change code

Factory settings

 

Info

Menu preferences

OSD

&Select OSD.

éPress the cursor right to select Normal or Minimum.

Normal to activate the continuous display of the channel number (for 10 minutes) and extended display of TV channel and programme information on screen. E.g. information on the main or auxiliary programme, input signal quality of connected peripheral equipment, the display format and sound mode.

Minimum to activate the display of reduced channel information. See Use of the remote control, p. 4, i Display information.

Programme title

&Select Programme title.

éPress the cursor right to select Programme title Yes or No.

When selected Yes, after the selection of a TV programme or after pressing the i key on the remote control, a TV channel may transmit the name of the TV channel or the programme title.

When selected No, the programme title will only appear after pressing the i key and not after the selection of a TV channel.

Set/Change code

&Select Set or Change code in the Features preferences menu with the cursor down.

éIf no PIN-code exists yet, the menu item is set to Set code. Follow the instructions on screen.

If a PIN-code has previously been entered, the menu item is set to Change code. Follow the instructions on screen.

All number combinations from 0000 tot 9999 are valid numbers.

“The Features preferences menu reappears with a message confirming that the PIN has been created.

Important:You have forgotten your code !

&Select Change code in the Features preferences menu and press OK.

éPress the cursor right and enter the overriding code 8-8-8-8.

“Press the cursor again and enter a new personal 4-digit code.The previous code is erased and the new code is stored.

Factory settings

This function allows you to reset most of the picture and sound settings to their predefined factory states.

&Select Factory settings with the cursor down.

éPress the cursor right.

“Press the OK key to erase settings and reset them to their default values.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents
Contents First time installation PreparationTo operate the motorised swivel Keys at the top of the TVOperation Automatic positioning to central positionUse of the remote control RC4310 Dual screen/PIP Define the position of the PIP screenPicture format Alphanumeric keys on the remote control Browse screenTelevision MultimediaHow to navigate through the Settings menus To use the menusDemo Introduction Installation Automatic installation Manual installation Select the menu languageReshuffle/Rename channels ReshuffleRename Preferred channelsSoftware upgrade USB device/Memory Card upgradeSetup menu Features preferences TeletextPreferences Picture/sound preferencesFactory settings Menu preferencesProgramme title Set/Change codeSource Digital AudioTV menu Picture menuDigital options Dynamic contrastColour enhancement HueSound menu Features menu SleeptimerOn timer Select subtitlesAmbilight in Standby mode Ambilight menuSmart colour modes Viewing content from a Memory card / USB device Multimedia BrowserInserting a memory card / USB device Removing the memory card / USB deviceOther function keys on the remote control Multimedia Browser menuFollowing icons may appear Function keys at the bottom of the screenTeletext Equipment to connect to the side connections Teletext menuConnect Peripheral Equipment Recorder VCR-DVD+RW If your recorder has an S-VHS video jackRecorder and other equipment DVD Player or other accessory digital source equipment Devices with Component Video Output Connectors YPbPrDevices with an S-Video connector Devices with RGB outputMultiChannel Surround receiver Digital MultiChannel Surround receiverHdmi Devices to connect to a DVI connector VGARecord with your recorder To select connected peripheralsRecord a TV programme Record a programme from Monitor OUTNormal mode Expert modeAudio- and video equipment keys Direct selection of a connected peripheral equipmentSetting the remote control to work peripheral equipment Code setupTo cancel the selected mode Digital Video Disc DVD Satellite ReceiverLearnable remote control DVD/RPage Tips Check if the source complies with a supported codePreparing a portable memory for software upgrade Verifying the version of the TV softwareAutomatic software upgrade procedure Manual software upgrade procedureAnnex 2 Philips TV Slideshow Format with background music General RulesGeneral Format Supported XML-tags ExamplesTag Name Use Description Digital Content Issues Portable Memory IssuesDigital Camera Issues Annex 3 Philips TV Portable Memory and USBUSB Memory Device Issues
Top Page Image Contents