Panasonic PV-V4022-A warranty Tape Operation

Page 10

Tape Operation

Tape Operation

• Tape

Search System

For each recording, an invisible index mark is placed on the tape. A program index and information are also included for timer recordings. These marks are used to access or scan recordings.

Repeat Play

Set to playback a recording over and over.

1 Press ACTION to display menu.

Commercial Skip

VCR fast forwards (skips) over 1~3 minutes of recorded tape.

1 Press CM/ZERO in Play mode.

Operation

Index Search

1

 

SEARCH

 

INDEX

 

PROGRAM END

ENTER INDEX NUMBER :1

USING 1- 9 KEYS

FORWARD SEARCH :FF

REVERSE SEARCH :REW

NEXT :SEARCH

EXIT :STOP

Press SEARCH* to display SEARCH in Stop or Play mode, and then press NUMBER keys to select recording number.

To calculate number, see below.

Press FF or REW to start search.

Program End Search

Locates end point of recording for continuity.

1 Press SEARCH twice to display SEARCH

in Stop or Play mode.

2

 

SEARCH

Press FF

 

INDEX

 

PROGRAM END

to start PROGRAM

 

 

 

 

 

 

 

 

END SEARCH.

 

SEARCH START :FF

• To cancel, press

 

 

 

 

 

EXIT :SEARCH

STOP or PLAY.

2

 

 

 

 

 

 

Press

VCR

 

 

CLOCK

 

CHANNEL

 

REPEAT

PLAY

:OFF

to select REPEAT PLAY

 

REMOTE

WARNING

:ON

 

AUTO SHUT- OFF

:OFF

and press to set ON

 

AUTO VCR/TV

:ON

 

IDIOMA/LANGUE : ENGLISH

or OFF.

 

VCR’ S OUTPUT CH

:3

 

SELECT :

SET :

ON : Play repeats at

 

EXIT : ACT I ON

 

tape end or if unrecorded portion over 30 sec. is detected.

3 Press ACTION to return to normal screen.

Press CM/ZERO repeatedly to change skip time as shown below.

PLAY

1st Press 1 min Skip

2nd Press

2 min Skip

3rd Press 3 min Skip

2

INDEX SEARCH

FORWARD SEARCH :FF REVERSE SEARCH :REW

Play begins at search end. To search forward or back 1 index, press

FFor REW while screen left is displayed (10 sec.).

To cancel, press STOP or PLAY.

Examples of Program End Search.

Fig. 1

Program 1

INDEX

Program 2 or BLANK

the current tape position Press SEARCH button

 

End Point

FF

Fig. 2

Zero Search

To quickly return to a specified tape location.

1 Press DISPLAY during play

to display Counter.

2

PLAY 12 : 0 0AM

Press RESET

 

0 : 00 : 00

• No indication appears.

To Calculate Index Number

Example 1:

To go to rec. 2 from rec. 4, enter 3 and press REW.

1

2

3

4

 

5

6

7

 

 

 

 

 

 

 

 

 

INDEX

Program 1

BLANK

INDEX

Program 2

BLANK

 

 

 

the current tape position

 

 

 

 

 

Press SEARCH button

 

End Point

 

 

 

 

FF

 

Fig. 3

the current tape position

 

 

 

 

 

 

 

 

 

 

Press SEARCH button

 

 

 

INDEX

Program 1

BLANK

 

 

Program 2

 

 

 

 

 

 

 

 

If search

End Point

 

FF

 

 

exceeds a few

 

 

 

 

 

 

 

 

 

 

 

 

 

seconds in

 

 

 

 

 

BLANK area.

 

SP

COUNTER at desired

 

 

position to reset to

 

 

“0:00:00”.

3

Continue to record, playback, etc.

4

Press STOP.

 

5

REW 12 : 3 0AM CH 02

Press CM/ZERO in Stop

0 : 30 : 30

mode to start ZERO

SP

 

 

SEARCH.

Example 2:

To go to rec. 6 from rec. 2, enter 4 and press FF.

1

2

3

4

5

6

7

 

 

 

 

 

 

 

NOTE: indicates start points of each recording.

Note

If Index Search is started very close to an index mark, that index mark may not be counted in the search.

Upon locating end point,

search continues 7 sec. past end point,

tape rewinds to 10 sec. before end point,

tape plays to end point and stops.

Notes

If Program End Search is started very close to an index mark, that mark may be skipped over.

To cancel, press PLAY or STOP.

• Unit will go into FF or

REW mode and stop at

the last point the

Counter was set to

0:00:00.

STOP 12 : 3 1AM CH 02

0 : 00 : 00

SP

*Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again.

- 6 -

- 7 -

Image 10
Contents Model No. PV-V4022-A Table of Contents Limited WarrantyCustomer Services Directory Basic OperationsBefore Using Important Safeguards and PrecautionsSafety Precautions Initial Setup Clock Set Select Channel Playback Record Auto For DSS/Cable Box VCR TVLocation of Controls Timer RecordingTimer Buttons, Front ViewPara Ant/Cable VCR TV Varios Advanced Operations Clock, Time Zone Adjust, VCR’s Output Channel DSTBefore Requesting Service Model No. PV-V4022-AAdvanced Connections Multi-Brand Control FeatureFeature Advanced Connections Multi-Brand ControlDisplays OSD Blank Tape/No Video Signal IndicationsOn-Screen Displays OSD Function & Channel DisplaysTape Operation Connection Copying Your Tapes DubbingPlaying Source VCR Recording Editing VCR VCR Features Copy Your Special VCR FeaturesBefore Requesting Service Tapes Dubbing