PREPARATION FOR USE |
| SETUP |
VCR to TV Connection
1 | Disconnect the AC power cord of the TV from the | ||
AC outlet. |
| ||
2 | Disconnect the antenna or cable from the TV. | ||
3 | Connect the antenna or cable to the ANT. IN jack of | ||
the VCR. |
|
| |
4 | Connect the VCR to the TV using the RF cable. | ||
5 | Plug the AC power cords of the VCR and TV into | ||
the AC outlets. |
| ||
[VHF/UHF | [Indoor antenna] | [Back of the VCR] | |
combination antenna] |
| [Back of the |
UHF/VHF combination TV]
|
| OR | IN | RF cable |
|
|
| ANT |
|
|
|
|
| (supplied) |
[Cable | box or satellite box] |
|
| UHF/VHF |
OR | OUT |
| ||
From Cable or |
|
|
|
|
Satellite Company |
|
|
|
|
RF Output Channel
If your TV does not have A/V terminals:
Press [PLAY] on the VCR for 3 seconds during playback.The RF output channel will change to CH4 from CH3.
When you want to return to CH3 for RF output channel, press [PLAY] on the VCR for 3 seconds during playback again. (Default setting :CH3)
•There is case that the RF output channel does not change by situation (For example, when you adjust tracking using [CHAN-
NEL () ].
In this case, stop the playback, and start the playback again. After that, press [PLAY] on the VCR for 3 seconds.
•If there is a power failure or the VCR is unplugged for more than 30 seconds, the RF output channel setting will return to CH3.
VCR to AV TV connection using AUDIO/VIDEO Cables
Using Optional AUDIO/ VIDEO Output Jacks
With this connection, you can get better pictures and sounds when playing back a tape if your TV has A/V Input jacks. Please refer to your TV’s owner’s manual.
Using AUDIO/VIDEO Input Jacks
You can use the A/V input jacks on the front or the back of the VCR.
•To use the input jacks on the back of the VCR, select "L1" position by pressing [0], [0], [1] on the remote control or
[CHANNEL () ].
•To use the input jacks on the front of the VCR, select "L2" position by pressing [0], [0], [2] on the remote control or
[CHANNEL () ].
•“L1” or “L2” is found before the lowest memorized channel. (Example: CH2)
[Playing VCR]
AUDIO
L
OUT | IN |
|
|
| R |
|
|
VIDEO |
|
| |
OUT | IN | Audio/Video cables | |
|
|
| (not supplied) |
|
|
| [TV A/V] |
| IN |
|
|
| L |
| R |
|
| AUDIO | VIDEO |
Automatic Channel Set Up
You can automatically program the tuner to scan only the channels you receive in your area.
•Channel memory programming is NOT needed when you connect the VCR to a cable box or satellite box as in "Connect VCR to TV Connection". In this case, select the VCR and TV to channel 3 or 4 the same channel as the RF output channel of the VCR. Then, the channel you want to record or view may be selected at the cable box or satellite box.
•Follow the steps below once. Repeat it only if there is a power failure or if the VCR is unplugged for more than 30 seconds. (In these cases, the programmed channels are erased.)
•You must follow the steps below before attempting to play or record a video tape. If you want to play or record a video tape BEFORE programming the tuner, you can cancel it by press- ing [COUNTER RESET/EXIT].
1 | You need to connect the antenna or cable to the | ||||
VCR first. Then, connect the VCR power plug into a | |||||
|
| standard AC outlet. |
|
| |
2 | Turn on the TV and set the TV to channel 3. If chan- | ||||
nel 3 is already occupied for broadcasting, change the | |||||
|
| RF output to CH 4, and change the TV channel to CH4. | |||
|
| (See “RF Output Channel” on page 3 for the detail.) | |||
|
|
|
| ||
3 | Turn on the VCR by pressing [POWER]. When the | ||||
POWER is on, both the POWER and VCR indicators | |||||
|
| on the VCR will be on. |
|
| |
|
|
|
|
| |
4 | Select the On Screen Language | LANGUAGE SELECT |
| ||
("ENGLISH" , "FRANCAIS" or | |||||
ENGLISH | |||||
|
| "ESPAÑOL") by pressing [PLAY] or | FRANCAIS | ||
|
| [STOP]. Then, press [F.FWD]. |
|
| |
5 | Begin channel preset by pressing [F.FWD] once. The | ||||
tuner scans and memorizes all active | CH 01 | ||||
|
| channels in your area. |
|
| |
| • The VCR distinguishes between standard | AUTO SET UP | |||
|
|
| |||
|
| TV channels and cable channels. |
|
| |
6 | After scanning, the tuner stops on the lowest mem- | ||||
orized channel. The TV screen returns to TV mode. |
•If "AUTO SET UP" appears on the TV screen again, check the cable connections. Press [F.FWD] once again and the VCR will begin preset again.
To Select a Desired Channel
You can select the desired channel by using [CHANNEL
() ] or directly pressing [Number] on the remote control.
Note for using the Number buttons:
•When selecting cable channels which are higher than 99, enter channel numbers as a
•You must precede
To Preset the Channel Again
|
|
|
1 | Press [MENU] until the main menu appears. | |
|
|
|
2 | Select "CHANNEL SET UP" by pressing [PLAY] or | |
[STOP]. Then, press [F.FWD]. | ||
|
|
|
3 | Select "AUTO SET UP" by pressing [PLAY] or | |
[STOP]. Then, press [F.FWD]. After scanning, the |
tuner stops on the lowest memorized channel.
– 3 – | EN |