JVC HR-A230EK SET A/B Code Switch, RE-SUPPLY Power, Next Function Memory, Ntsc Playback

Page 14

14

OPERATE

PLAY

 

EW

q 6

OPERATE

A/B CODE

2

 

1

2

3

4

5

6

7

8

9

 

0

 

REW

PLAY 3 1

Next Function Memory

You can set your recorder's power to go off automatically after the tape is fully rewound. Before starting, make sure the recorder is in the Stop mode.

For Automatic Power Off After Tape Rewind . . .

. . . press REW, then press OPERATE within 2 seconds.

PLAYBACK (cont.)

NTSC Playback

Your video recorder is equipped with NTSC circuitry that can play back NTSC tapes.

1

 

LOAD A CASSETTE

 

Insert a cassette recorded in NTSC.

2

 

START PLAYBACK

 

Press PLAY. “NT” appears on the display panel.

 

 

 

● Some TVs shrink the picture vertically and place

 

black bars at the top and bottom of the screen. This is

 

 

not a malfunction on the part of either the video

 

 

recorder or the TV.

 

 

● The picture may roll up and down. This can be

 

 

corrected using the V-HOLD control found on some

 

 

TVs. (This cannot be corrected if the TV does not

 

 

have a V-HOLD control.)

 

 

● The counter and elapsed tape time readings will be

 

 

incorrect.

 

 

● During search, still, or frame-by-frame playback, the

 

 

picture will be distorted, and there may be a loss of

 

 

colour.

 

 

● Depending on the type of TV, the top and bottom

 

 

portions of superimposed displays may be cut off

 

 

during NTSC playback.

 

 

 

Remote A/B Code Switching

The remote control is capable of controlling two JVC video recorders independently; one set to respond to the remote control’s A code control signals and another set to respond to B code control signals. The remote control is preset to send A code signals because your video recorder is initially set to respond to A code signals. You can easily modify your video recorder to respond to B code signals.

1

 

REMOVE POWER SUPPLY

 

Unplug the mains power cord from the mains outlet.

2

 

SET A/B CODE SWITCH

 

Set to B.

3

 

RE-SUPPLY POWER

 

Plug the mains power cord back into the mains outlet.

4

 

TURN THE RECORDER ON

 

Press OPERATE on the remote control. The recorder

 

will now only respond to B code signals.

 

 

 

NOTE:

Some TV sets may malfunction in response to the B mode. If this happens, switch back to the A mode.

Page 13 Page 15
Image 14
Page 13 Page 15
Contents HR-A230EK HR-A231EK Do not place the recorder Safety PrecautionsSafety First Step Quick SET UP Basic Connections Check ContentsInstalling Your N EW Recorder Situate RecorderReset Output Mode Select Output ModeSET TV Preset Tune The TV To Your Video RecorderSatellite Receiver Connection To Satellite ReceiverInst Allin G Your NEW RE C Order contd UnitTuner Set Access ConfirmationInitial Settings Return to NormalTurn the Recorder on Access Clock SET DisplayClock Set SET ClockSET Date and Time Preset PositionReturn to Normal Display SET Just ClockPoint Basic PlaybackLoad a Cassette Start PlaybackActivate SLOW-MOTION Playback Playback FeaturesPlayback SearchManually Adjust TrackingOverride Automatic Tracking Return to AutomaticIndex Search Activate Index SearchActivate Repeat Repeat PlaybackRemote A/B Code Switching SET A/B Code SwitchRE-SUPPLY Power Next Function MemoryBasic Recording Recording Features SET Display Timer RecordingInformation On Video Plus+ Guide Channel SetTimer RECORDINGcont NumberAccess Programme Video Plus+ Timer RecordingAccess Timer Program Ming Display Enter Pluscode NumberEngage RECORDER’S Timer ModePress Timer Press SP/LP to set the tape speedEnter Programme Start Time Regular Timer ProgrammingAccess Programme Display Enter Programme DatePress TV PROG. + Enter Preset PositionEngage RECORDER’S Timer Mode Revise Programme Information Check And Cancel ProgrammesWith the recorders power turned on, go to step PDC RecordingMake Connections SET Recording DECK’S Input ModeEdit To Or From Another Video Recorder Start Source PlayerMode Edit From a CamcorderSET RECORDER’S Input Start CamcorderInput Channel Using the Confirmation D IsplaySelect Position Enter NEW ChannelSelect Item Select StationDelete Station Select NEW PositionSelect NEW Station Switch StationsUsing the Confirmation Display CharacterFine-Tuning Channels Already Stored Access Manual CH. SET DisplayPerform Tuning Select Channel to FINE-TUNETV Statio N and ID List Ridge Hill Bluebell HillChannel Islands Set the TV to its AV mode Panel Indicator offIf you are using the AV connection ClearMade, Auto Channel Set was Disappeared Performed Timer againTV/VCR switch is in the wrong Set the switch to TV Questions and Answers Programme Delivery Control PDC IndexList Of Terms Front View ANT. in Connector enables connection of aerial. pg Rear ViewRemote Control Operating JVC TVs Installing BatteriesHow To Use Digit EntrySpecifications
Top Page Image Contents