JVC HR-VP636U manual Important Product Safety Instructions

Page 3

IMPORTANT PRODUCT SAFETY INSTRUCTIONS

Electrical energy can perform many useful functions. But improper use can result in potential electrical shock or fire hazards. This product has been engineered and manufactured to assure your personal safety. In order not to defeat the built-in safeguards, observe the following basic rules for its installation, use and servicing.

ATTENTION:

Follow and obey all warnings and instructions marked on your product and its operating instructions. For your safety, please read all the safety and operating instructions before you operate this product and keep this booklet for future reference.

INSTALLATION

1. Grounding or Polarization

(A)Your product may be equipped with a polarized alternating- current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature.

If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

(B)Your product may be equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature.

If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

2. Power Sources

Operate your product only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. If your product is intended to operate from battery power, or other sources, refer to the operating instructions.

3. Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

4. Power Cord Protection

Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against

3

5. Ventilation

Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered.

•Do not block the openings by placing the product on a bed, sofa, rug or other similar surface.

•Do not place the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

6. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

ANTENNA INSTALLATION

INSTRUCTIONS

1. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

2. Lightning

For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

3. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

ANTENNA

LEAD IN WIRE

GROUND CLAMP

them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

ELECTRIC SERVICE EQUIPMENT

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING

CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H)

NEC – NATIONAL ELECTRICAL CODE

Page 2 Page 4
Image 3
Page 2 Page 4
Contents HR-VP636U Do not place the VCR Dear CustomerImportant Product Safety Instructions Should be moved with care. Quick Product and cart combinationContents Basic Connections During Auto Clock Set Dual Quick SetPerform Dual Quick SET Initial Settin GSClock Select Host Channel Clock SettingSelect Time Zone Select D.S.T. ModeCH or Shuttle Plus Select ModeMake Corrections CH or Shuttle Plus 5, then press OKTuner Access Main MenuAccess Tuner SET Access Band ScreenReturn to Normal Screen Perform Auto Channel SETStore Desired Channel Access Tuner SET ScreenAccess AFC Screen Make SelectionConnect Cable BOX to VCR Tuner Cable Box ControllerSituate Controller Attach ControllerAccess Cable BOX Output ScreenSet Cable Box Output Channel Set Cable Box Brand Return to VCR PLUS+ SET-UP ScreenTurn on Cable BOX Brand SET ScreenYou can now set up the VCR Plus+ feature pg Access Main Menu Screen VCR Plus+ SetupInput Guide Channel Number Access Custom SET ScreenAccess VCR PLUS+ SET-UP Screen Access Guide Channel SET ScreenInput Receiving Channel Number Start Playback Simple PlaybackLoad a Cassette Find Program Start PointSimple Recording During Playback FRAME-BY-FRAMEPlayback Resume NormalManual Tracking Engage Manual Tracking ModeAdjust Manual Tracking RE-ENGAGE Automatic TrackingReturn to Normal Access Function SETAccess Audio Monitor Playback and Recording FeaturesSuperimpose Stop Repeat Access Distant CodeSkip Over Unwanted Sections Start RepeatMemory Reset Counter to ZeroActivate Instant Review Activate CounterAV Compu Link Playback Tape Position IndicatorMake Connection Next-Function MemoryPerform AV Compu Link Playback Access Function SET ScreenAccess Special Function Screen Enable AV Compu Link PlaybackActive Video Calibration Access Video Calibration ScreenBegins with the picture level optimized RecordingVCR takes about Seconds to assess Quality of the tape Use, then recordingTape in use PlaybackRecord One Program While Watching Another Engage TV ModeSelect Channel for Viewing Display Elapsed Time on ScreenTo Record Stereo Programs Access 2ND AudioStereo And SAP Second Audio Program To Record SAP ProgramsEnter Program Information VCR Plus+ Timer ProgrammingTimer Recording Check Input DataPress SP/EP Engage Timer ModePress TIMER. The VCR turns off automatically CHECK/CORRECT Input DataAccess Program SET Screen Instant Timer Recording ITROn-Screen Timer Programming Engage ITR ModeSET Program Information Select Program NumberRE-ENGAGE Timer Disengage TimerAccess Program SET Cancel a ProgramOFF by pressing CH5 Access Auto TimerAuto Timer Your choice on orEdit To Or From Another Edit From a Camcorder Shuttle Plus 5 . If Assemble Editing SET TV Brand Code SET Remote Control ModeSpeci AL Features Turn on the TV24, 25 01, 02, 03, 04, 05, 06, 0715, 16, 17 19, 20Cord SET A/B Code SwitchPlug in Power Cord Turn VCR Power onCassette gets stuck partway TroubleshootingRecording Timer againDoesn’t work properly Re-perform the VCR Plus+ setupProcedure pg RoubleshootingPlayback Quest Ions and AnswersMaximum recording time EIA monochrome signalYear programmable timer 20C to 60C -4F to140FMBR Multi-Brand Remote Code Setting IndexList Of Terms Front View Front Display Panel Remote Control ProvidedFor Servicing HOW to Locate Your JVC Service CenterLimited Warranty WarrantyHR-VP636U
Top Page Image Contents