JVC HR-VP636U manual Basic Connections

Page 6

6INSTALLINGYOURNEWVCR

Basic Connections

Antenna or Cable

Coaxial Cable

 

Flat Feeder

 

AC Power

Maching Transformer

 

 

 

Cord

 

 

Back of VCR

ANTENNA-IN

RF

 

AC Outlet

(Antenna or Cable input)

OUT

 

 

TV

RF Cable

(provided)

 

 

75 ohm terminal

Back of VCR

AUDIO

L

VIDEO

CH3 CH4

 

CHECK CONTENTS

 

Make sure the package contains all of the accessories

1 listed in “SPECIFICATIONS” (☞ pg. 54).

 

SITUATE VCR

2 Place the VCR on a stable, horizontal surface.

3

CONNECT VCR TO TV

The connection method you use depends on the type of

TV you have.

 

RF Connection

 

● To Connect To A TV With NO AV Input Terminals . . .

 

a– Disconnect the TV antenna from the TV.

 

b– Connect the TV antenna cable to the ANT IN jack

 

on the rear of the VCR.

 

c– Connect the supplied RF cable between the RF

 

OUT jack on the rear of the VCR and the TV’s

 

antenna terminal.

AV Connection

●To Connect To A TV With AV Input Terminals . . .

a– Connect the antenna, VCR and TV as shown in the illustration.

b– Connect an Audio/Video Cable (not supplied) between the AUDIO OUT and VIDEO OUT jacks on the rear of the VCR and the AV IN jacks on the TV.

 

CONNECT VCR TO

4

POWER SOURCE

Connect the power plug to an AC outlet.

 

● The clock will automatically be set when the antenna

is connected and when the AC is first connected to

 

the VCR (☞ pg. 7).

 

 

 

FINAL PREPARATION FOR

5

USE

Select the VCR channel (3 or 4) by setting the switch

on the rear of the VCR as shown in the illustration.

Turn on the power to the TV. You are now able to perform

 

 

simple playback (☞ pg. 22) and recording (☞ pg. 23).

 

(If 'Auto' is displayed on the front display panel, the

 

clock is being set automatically. Wait for the time to be

 

displayed before powering on the VCR.)

NOTES:

●The VCR channel is the channel on the TV which will display the audio and video signals from the VCR. The VCR's CH3- CH4 switch sets the VCR channel to CH3 or CH4.

●The CH3–CH4 switch is preset to the CH3 position. Set to CH4 if CH3 is used for broadcasting in your area.

●If your TV has no AV input terminals, set the channel on the TV to correspond to the CH3–CH4 switch on the back of the VCR.

●Even if your TV has AV input terminals, you must connect it to the VCR using an RF cable in order to record one show while watching another (☞ pg. 35).

●For full identification of the VCR's rear panel, refer to the Index (REAR VIEW ☞ pg. 56).

Page 5 Page 7
Image 6
Page 5 Page 7
Contents HR-VP636U Dear Customer Do not place the VCRImportant Product Safety Instructions Product and cart combination Should be moved with care. QuickContents Basic Connections Initial Settin GS Dual Quick SetPerform Dual Quick SET During Auto Clock SetClock Clock Setting Select Host ChannelSelect D.S.T. Mode Select Time ZoneCH or Shuttle Plus 5, then press OK Select ModeMake Corrections CH or Shuttle PlusAccess Band Screen Access Main MenuAccess Tuner SET TunerPerform Auto Channel SET Return to Normal ScreenMake Selection Access Tuner SET ScreenAccess AFC Screen Store Desired ChannelAttach Controller Tuner Cable Box ControllerSituate Controller Connect Cable BOX to VCRAccess Cable BOX Output ScreenSet Cable Box Output Channel Brand SET Screen Return to VCR PLUS+ SET-UP ScreenTurn on Cable BOX Set Cable Box BrandYou can now set up the VCR Plus+ feature pg VCR Plus+ Setup Access Main Menu ScreenAccess Guide Channel SET Screen Access Custom SET ScreenAccess VCR PLUS+ SET-UP Screen Input Guide Channel NumberInput Receiving Channel Number Find Program Start Point Simple PlaybackLoad a Cassette Start PlaybackSimple Recording Resume Normal FRAME-BY-FRAMEPlayback During PlaybackRE-ENGAGE Automatic Tracking Engage Manual Tracking ModeAdjust Manual Tracking Manual TrackingPlayback and Recording Features Access Function SETAccess Audio Monitor Return to NormalSuperimpose Start Repeat Access Distant CodeSkip Over Unwanted Sections Stop RepeatActivate Counter Reset Counter to ZeroActivate Instant Review MemoryNext-Function Memory Tape Position IndicatorMake Connection AV Compu Link PlaybackEnable AV Compu Link Playback Access Function SET ScreenAccess Special Function Screen Perform AV Compu Link PlaybackAccess Video Calibration Screen Active Video CalibrationQuality of the tape Use, then recording RecordingVCR takes about Seconds to assess Begins with the picture level optimizedPlayback Tape in useDisplay Elapsed Time on Screen Engage TV ModeSelect Channel for Viewing Record One Program While Watching AnotherTo Record SAP Programs Access 2ND AudioStereo And SAP Second Audio Program To Record Stereo ProgramsCheck Input Data VCR Plus+ Timer ProgrammingTimer Recording Enter Program InformationCHECK/CORRECT Input Data Engage Timer ModePress TIMER. The VCR turns off automatically Press SP/EPEngage ITR Mode Instant Timer Recording ITROn-Screen Timer Programming Access Program SET ScreenSelect Program Number SET Program InformationCancel a Program Disengage TimerAccess Program SET RE-ENGAGE TimerYour choice on or Access Auto TimerAuto Timer OFF by pressing CH5Edit To Or From Another Edit From a Camcorder Shuttle Plus 5 . If Assemble Editing Turn on the TV SET Remote Control ModeSpeci AL Features SET TV Brand Code19, 20 01, 02, 03, 04, 05, 06, 0715, 16, 17 24, 25Turn VCR Power on SET A/B Code SwitchPlug in Power Cord CordTroubleshooting Cassette gets stuck partwayTimer again RecordingRoubleshooting Re-perform the VCR Plus+ setupProcedure pg Doesn’t work properlyQuest Ions and Answers Playback20C to 60C -4F to140F EIA monochrome signalYear programmable timer Maximum recording timeMBR Multi-Brand Remote Code Setting IndexList Of Terms Front View Remote Control Provided Front Display PanelHOW to Locate Your JVC Service Center For ServicingWarranty Limited WarrantyHR-VP636U
Top Page Image Contents