Editing

– Other Functions –

	CABLE BOX OR SATELLITE	CODE
	RECEIVER BRAND	CODE
	RECEIVER BRAND

	JVC	72, 73,
	AMSTRAD	60, 61, 62, 63, 92
	BT	72
	CANAL+	81
	CANAL SATELLITE	81
	D-box	85
	ECHOSTAR	51, 78, 79, 80, 82
	FINLUX	68
	GALAXIS	69, 88
	GRUNDIG	64, 65
	HIRSCHMANN	64
	ITT	68
	JERROLD	01, 04, 06, 11, 12, 15, 28, 75
	KATHREIN	70, 71
	LUXOR	68
	MASPRO	70
	NOKIA	68, 87
	PACE	67, 86, 92
	PANASONIC	13, 14, 74
	PFT	69
	PHILIPS	66, 84
	PHONOTREND	69
	SALORA	68
	SKYMASTER	69
	TPS	83
	VIDEOWAY	03, 09, 22, 76, 77
	WISI	64

DVD BRAND	CODE

JVC	55
PANASONIC	58
PHILIPS	56
TOSHIBA	57

Changing Remote Control Code

This remote control is capable of transmitting two control codes; one set to respond to A code control signals and another set to respond to B code control signals. This remote control is preset to send A code signals because your recorder is initially set to respond to A code signals. You can easily modify your recorder and the remote control to respond to B code signals. When using two JVC recorders, set two recorders and their remote controls to different codes, so that you can operate these recorders separately.

ASet remote control code for remote control

APress and hold VCR.

BPress the Number key “2”. C Press OK, and release VCR.

● The remote control now can transmit B code control signals.

BCheck remote control code for recorder

Press and hold PLAY (4) on the recorder for more than 5 seconds while the recorder is turned off. The code currently set appears on the display panel.

CChange code for recorder

Press any key on the remote control. The recorder now responds to B code control signals.

●To set the remote control and the recorder back to A code control signals, repeat the same procedure as shown above except pressing the Number key “1” in step B of 1.

To control two recorders with the same remote control

You can control two JVC recorders by switching the remote control code for the remote control between A and B ( step A), keeping two recorders to different control codes.

●To change only the remote control code for the remote control, DO NOT perform steps B and C.

You can use your recorder as the playback or recording deck.You can use a camcorder as the source player and your recorder as the recording deck. Refer also to the other components’ instruction manuals for connection and its operations.

AMake connections

Example: When using this recorder as the source player

This recorder (for playback)

To AUDIO/VIDEO OUT

AV cable (not supplied)

To AV input

Another recorder (for recording)

●When using this recorder as the recording deck, connect this recorder’s AV input connectors to the AV output connectors on the other recorder. If the source player is monaural, connect the audio output connector on the source player to the left audio input connector on this recorder.

BLoad cassettes

Insert the playback cassette into the source player and the cassette to be recorded on into the recording deck.

CSelect input mode on recording deck

Select the correct external input on the recording deck.

On this recorder (when using this recorder as the recording deck); Select “L-1” — when connecting the other recorder to the AV input connectors on the rear panel.

(Only for HR-J485EA)

Select “F-1” — when connecting the other recorder to the AV input connectors on the front panel.

On the remote control

Press AUX or PR+/–.

On the recorder

Press PAUSE[PR], and then FF[PR+] or REW[PR–]. See step B in “Basic Recording”.

DSelect edit mode

Set the edit mode to “ON” for the recorders if such a mode is equipped.

●On this recorder, set “PICTURE CONTROL” to “EDIT”.

EStart playback

Press PLAY (4) on the source player.

FStart recording

Press REC (7) on the recording deck.