JVC LPT0593-001A, HR-J485EA, HR-J285EA Timer Recording, CODESystem Setup, CODETimer Programing

[0–9] OR [ / ] : SELECT

[MENU] : EXIT

G-CODE SETUP

TV PROG 1

– P1 –

NO. 12345678

START STOP

21:00 22:00

SP

: [OK]

DATE 25.04

Timer Recording

Up to 8 timer recording programs can be made using G-CODEtimer programing or Express timer programing method as far as a year in advance. Remember, the clock must be set before you can program the timer.

NOTES:

●If all the 8 programs have already been set, “PROGRAM FULL” appears on the TV screen.

●After timer recording is completed, the recorder turns off automatically.

●You can program the timer recording while a regular recording is in progress; the menu screens will not be recorded.

●In case of a power failure after programming, the recorder’s memory backup keeps your selections (if the lithium battery is not exhausted).

G-CODESystem Setup

INFORMATION

The G-CODEtimer programming system eliminates the need to input channel, date, start and stop time data when setting the timer record function. Simply key in the G-CODEnumber for the TV programme you wish to record (found in most TV listings) and the recorder's timer is automatically programmed.

You have to set “GUIDE PROG” numbers, which are assigned to each station for purposes of G-CODEtimer programming, for all the stations stored in your recorder’s memory to get proper results.

Before G-CODEsetup you must have performed the procedures of Tuner Set and Clock Set.

IMPORTANT

Perform the following procedure after Auto Set Up and/or the channel setting steps.

After setting the Guide Program Numbers, channel positions may be incorrect if you stored or skipped channels. In this case, re- perform Guide Program Number setting.

Guide Program Number Set

AAccess Main Menu screen, then Initial Set screen

Press MENU on the remote control. Press rt to place the pointer next to “INITIAL SET”, then press OK or e.

BAccess G-CODESetup screen

Press rt to place the pointer next to “G-CODE SETUP”, then press OK or e.

C Input Guide Prog number	G-CODE SETUP
Press rt or the Number keys to select	GUIDE PROG	TV PROG
the Guide Program number as shown in
	2	5
the TV listing, then press OK or e.
	[0–9] OR [ /	] : SELECT
	[MENU] : EXIT
D Input receiving channel number	G-CODE SETUP
Press rt or the Number keys to select	GUIDE PROG	TV PROG
the number of the channel on which the
	2	5

Guide Program number’s broadcasts are received, then press OK or e.

● If the satellite broadcast is received on your recorder's auxiliary channel (“L-1”

or “F-1”), select “L-1” or “F-1” for the channel position to which the satellite receiver is connected.

●Repeat steps 3 and 4 as necessary.

EReturn to normal screen

G-CODETimer Programing

The G-CODEnumbers are the numbers next to the program in most TV listing. ● Remember, the clock must be set

before you can program the timer. ● Be sure to read “G-CODE®”.

● Load a cassette with the record safety tab intact. The recorder turns on, and the counter is reset, automatically.

● Select the appropriate colour system with “PAL/MESECAM” and “NTSC” in Function settings.

A Press PROG on the remote control to access the G-CODEscreen.

G-CODE NO.

[0 – 9]

[+/–] : EXPRESS PROGRAMING

[PROG] : EXIT

BPress the appropriate Number keys

to input the G-CODEnumber, then press OK. Check to make sure the setting is accurate on the G-CODEProgram screen.

G-CODE NO.

1 2 3 4 5 6 7 8

[0 – 9] [] : DELETE [PROG] : EXIT

● If the G-CODESetup screen appears after pressing OK, press the Number

keys, PR+/– or rt to input the	GUIDE PROG	TV PROG
number of the channel on which the	2	5
broadcast for the G-CODEnumber is
received on the recorder, then press	[0–9] OR [ /	] : SELECT
	[PROG] : EXIT
OK.

●To set the tape speed, press SP/LP/EP.

●To change the stop time, press STOP+/–.

●To timer-record daily (Monday–Friday) or weekly serials, press DAILY or WEEKLY. Pressing the button again makes the “DAILY” or “WEEKLY” display disappear.

At the programme check screen...

When the weekly serials are programmed, a day of the week appears. When the daily serials are programmed, “DAILY” appears.

●If you made a mistake, press & to access the G-CODEscreen again.

●If an incorrect G-CODEnumber or the one for a broadcast already finished has been inputted, “ERROR” is displayed for about 5 seconds, then the G-CODEscreen reappears.

CPress OK or PROG.

●If “PROGRAM OVERLAPPED” appears, see “Program overlap warning display”.

DPress #. The recorder turns off automatically and “#” is displayed on the display panel.

NOTE:

●If the tape reaches its end during timer recording, the recording stops and “#”, “” and “$” on the front display panel blink.

Press MENU on the remote control.