JVC HR-J6003UM manual Basic Connections

Page 4

4INSTALLINGYOURNEWVCR

Basic Connections

Antenna or Cable

Coaxial Cable

 

Flat Feeder

 

AC Power

Maching Transformer

 

 

 

Cord

 

 

Back of VCR

RF

 

ANTENNA-IN

AC Outlet

(Antenna or Cable input)

OUT

 

 

 

CHECK CONTENTS

 

Make sure the package contains all of the accessories

1 listed in “SPECIFICATIONS” (☞ pg. 42).

 

SITUATE VCR

2 Place the VCR on a stable, horizontal surface.

3

CONNECT VCR TO TV

The connection method you use depends on the type of

TV you have.

 

RF Connection

 

● To Connect To A TV With NO AV Input Terminals . . .

 

a– Disconnect the TV antenna from the TV.

 

b– Connect the TV antenna cable to the ANT IN jack

 

on the rear of the VCR.

 

c– Connect the supplied RF cable between the RF

 

OUT jack on the rear of the VCR and the TV’s

 

antenna terminal.

AV Connection

●To Connect To A TV With AV Input Terminals . . .

a– Connect the antenna, VCR and TV as shown in the illustration.

b– Connect an Audio/Video Cable (not supplied) between the AUDIO OUT and VIDEO OUT jacks on the rear of the VCR and the AV IN jacks on the TV.

CONNECT VCR TO

TV

RF Cable (provided)

75 ohm terminal

300 ohm terminal

POWER SOURCE

4 Connect the power plug to an AC outlet.

FINAL PREPARATION FOR USE

5 Select the VCR channel (3 or 4) by setting the switch on the rear of the VCR as shown in the illustration.

Back of VCR

RF OUT

CH3 CH4

Turn on the power to the TV. You are now able to perform simple playback (☞ pg. 10) and recording (☞ pg. 11).

NOTES:

●The VCR channel is the channel on the TV which will display the audio and video signals from the VCR. The VCR's CH3- CH4 switch sets the VCR channel to CH3 or CH4.

●The CH3–CH4 switch is preset to the CH3 position. Set to CH4 if CH3 is used for broadcasting in your area.

●If your TV has no AV input terminals, set the channel on the TV to correspond to the CH3–CH4 switch on the back of the VCR.

●Even if your TV has AV input terminals, you must connect it to the VCR using an RF cable in order to record one show while watching another (☞ pg. 23).

●For full identification of the VCR's rear panel, refer to the Index (REAR VIEW ☞ pg. 40).

Page 3 Page 5
Image 4
Page 3 Page 5
Contents HR-J6003UM This unit is produced to comply with Standard IEC Publ Do not place the VCRContents Basic Connections Clock Access Clock SET Screen Clock SettingSET Date and Time Make CorrectionsAccess Main Menu Access Tuner SETAccess Band Screen TunerReturn to Normal Screen Perform Auto Channel SETPress Menu as many times as necessary Access Tuner SET Screen Access AFC ScreenAccess Manual Channel SET ScreenSimple Playback Load a CassetteFind Program Start Point Start PlaybackSimple Recording Playback FRAME-BY-FRAMEPlayback Resume NormalEngage Manual Tracking Mode Adjust Manual TrackingRE-ENGAGE Automatic Tracking Manual TrackingAccess Function SET Access Audio MonitorSelect The Soundtrack MixSuperimpose Access Distant Code Skip Over Unwanted SectionsStart Repeat Stop RepeatActivate Instant Review Activate CounterMemory Return to Counter Position ZeroTape Position Indicator Make ConnectionNext-Function Memory AV Compu Link PlaybackAccess Function SET Screen S.T. Picture System Access Main Menu ScreenSystem Screen Recording Press and hold RECQuality of the tape Use, then recording Begins with the picture Level optimizedBefore beginning, perform steps 1 and 2 on PlaybackTape in use Engage TV Mode Reset Counter to ZeroRecording Select Channel for ViewingAccess 2ND Audio Stereo And SAP Second Audio ProgramTo Record SAP Programs To Record Stereo ProgramsInstant Timer Recording ITR On-Screen Timer ProgrammingEngage ITR Mode Access Program SET ScreenEngage Timer Mode Press TIMER. The VCR turns off automaticallySelect Program Number SET Program InformationDisengage Timer Access Program SETCancel a Program RE-ENGAGE TimerAccess Auto SP/EP Auto SP/EP TimerAccess Auto Timer Auto TimerEdit From a Camcorder Start Recorder SET RECORDER’S Input Mode Edit To Or From AnotherLoad Cassettes Start PlayerRandom As- semble Editing Prepare for EditingStart R.A. Edit Locate EDIT-OUT PointEND R.A. Edit SET Remote Control TV Multi-Brand Remote ControlTurn on the TV SET TV Brand CodeRemote control won’t function Batteries are discharged Make sure the window side is up,Timer Recording Timer againQuestions and Answers MBR Multi-Brand Remote Code Setting List Of TermsRamdom Assemble Editing connector pg Push JOG +Remote Control Provided Front Display PanelEIA monochrome signal 20C to 60C -4F to140FMaximum recording time Frequency-synthesized tuner
Top Page Image Contents