JVC HR-J633U manual Quest Ions and Answers, Playback

Page 41

QUESTIONSANDANSWERS

41

PLAYBACK

Q. What happens if the end of the tape is reached during playback or search?

A.The tape is automatically rewound to the beginning.

Q.Can the VCR indefinitely remain in the still mode?

A.No. It stops automatically after 5 minutes to protect the heads.

Q.During search, slow, still and frame-by-frame playback, I can’t hear any audio. What’s the problem?

A.This is normal.

Q.During search, still and frame-by-frame playback, the picture is intermittent. What’s the cause?

A.Picture loss occurs when these types of playback are attempted with a tape recorded in LP mode. Pressing PLAY to return to normal playback will restore the picture.

Q.When returning from multi-speed search to normal playback, the picture is disturbed. Should I be concerned about this?

A.No, it is normal.

Q.Noise bars appear during multi-speed search. What’s the problem?

A.This is normal.

Q.Other than preventing further recording, what effect does removing the safety tab have?

A.It disables marking of index codes.

Q.Sometimes, during Index Search, the VCR can’t find the program I want to see. Why not?

A.There may be index codes too close together.

RECORDING

Q. When I pause and then resume a recording, the end of the recording before the pause is overlapped by the new recording. Why does this happen?

A. This is normal. It reduces distortion at the pause and resume points.

Q. Can the VCR indefinitely remain in the Record-Pause mode?

A.No. The VCR automatically goes to its Stop mode after 5 minutes to protect the heads. In IT Record- pause mode the VCR shuts off automatically after 5 minutes.

Q.What happens if the tape runs out during recording?

A.The VCR automatically rewinds it to the beginning.

TIMER RECORDING

Q. REC and TIMER remain lit on the front display panel. Is there a problem?

A.No. This is a normal condition for a timer recording in progress.

Q.Can I program the timer while I’m watching a tape or a TV broadcast?

A.You won’t see the picture as it is replaced by the on- screen menu, but the audio from the program or tape you’re viewing is present.

ATTENTION:

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the power off and unplug the power cord. Then plug it in again and switch power on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 41
Contents HR-J633U Do not place the VCR Dear CustomerImportant Product Safety Instructions USE Contents Basic Connections Clock Access Mode Select Screen Access LanguageSelect Screen Select LanguageSelect Time Zone Select Host ChannelOr Shuttle Plus CH or Shuttle PlusSelect Mode Select D.S.T. ModeSET DATE, Time and D.S.T Make CorrectionsAccess Tuner SET Access Main MenuAccess Band Screen TunerReturn to Normal Screen Perform Auto Channel SETAccess Manual Access AFC ScreenMake Selection Channel SET ScreenLoad a Cassette Simple PlaybackFind Program Start Point Start PlaybackSimple Recording Playback FRAME-BY-FRAMEResume Normal During PlaybackAdjust Manual Tracking Engage Manual Tracking ModeRE-ENGAGE Automatic Tracking Manual TrackingAccess Audio Monitor Access Function SETLayback and Recording Features Select The SoundtrackSuperimpose Skip Over Unwanted Sections Access Distant CodeStart Repeat Stop RepeatActivate Instant Review Reset Counter to ZeroActivate Counter MemoryMake Connection Tape Position IndicatorNext-Function Memory AV Compu Link PlaybackPerform AV Compu Link Playback Access Special Function ScreenEnable AV Compu Link Playback Active Video Calibration Access Main Menu ScreenAccess Video Calibration Screen Quality of the tape Use, then recording RecordingVCR takes about Seconds to assess Start Playback PlaybackSelect Channel for Viewing Engage TV ModeDisplay Elapsed Time on Screen Record One Program While Watching AnotherStereo And SAP Second Audio Program Access 2ND AudioTo Record SAP Programs To Record Stereo ProgramsOn-Screen Timer Programming Instant Timer Recording ITREngage ITR Mode Access Program SET ScreenSET Program Information Engage Timer ModeSelect Program Number Access Program SET Disengage TimerCancel a Program RE-ENGAGE TimerAuto Timer Access Auto TimerAccess Function SET Screen Edit To Or From Another Edit From a Camcorder Shuttle Plus 5 . If Select InputAssemble Editing TV Multi-Brand Remote Control Speci AL FeaturesSET TV Brand Code TRY Operating TV Cable Box Multi-Brand Remote Control Special Features SET Cable BOX Brand Code TRY Operating Cable BOXTroubleshooting Roubleshooting Timer againPlayback Quest Ions and AnswersSpecifications List Of Terms IndexFront View Front Display Panel Remote Control ProvidedFor Servicing HOW to Locate Your JVC Service CenterLimited Warranty WarrantyHR-J633U
Related manuals
Manual 45 pages 62.99 Kb