JVC HR-S5400U manual Recording, Timer again

Page 61

E

N

61

RECORDING

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

1.

Recording won’t start.

● There’s no cassette loaded.

Insert a cassette.

● The loaded cassette has had its

Remove the cassette and cover the

record safety tab removed.

hole with adhesive tape, or load a

cassette on which the record safety

tab is intact.

2. TV broadcasts won’t record

● The VCR has been set to its AUX

Set the VCR to the appropriate

properly.

mode by mistake.

channel.

3. Tape-to-tape editing won’t work.

●The VCRs or the camcorder and the

Refer to the directions and the

VCR have been incorrectly con-

illustration under “Edit To Or From

nected.

Another VCR” (☞ pg. 49) or “Edit

From A Camcorder” (☞ pg. 50) and

properly connect the units.

● The power to one or more of the

Make sure the power to all units is on.

units has not been turned on.

● The recorder’s input mode has been

Select the recorder’s appropriate

set incorrectly.

input mode at the Aux Input Screen

(☞ pg. 51).

TIMER RECORDING

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

1.

Timer recording won’t work.

● The clock and/or the timer have

Set the clock and/or timer correctly.

been set incorrectly.

● The timer is not engaged.

Press TIMER and check to make sure

that TIMER appears on the front

display panel.

● The VCR has not been set up properly.

Re-perform the set-up procedures.

Make sure you have compensated for

Guide Channel and VCR or cable

box channel number mismatches

(☞ pg. 20).

2.

On-screen timer programming

● Timer recording is in progress.

Timer programming can’t be performed

won’t work.

when timer recording is in progress.

Wait until it finishes.

3.

TIMER and ] on the front

● The timer is engaged but there’s no

Load a cassette with the record safety

display panel won’t stop blinking.

cassette loaded.

tab intact, or with the hole covered

with adhesive tape.

4.

The cassette is automatically

● The loaded cassette has had its

Remove the cassette and cover its

ejected, and TIMER and ] on the

record safety tab removed.

hole with adhesive tape, or replace it

front display panel won’t stop

with a cassette on which the safety

blinking.

tab is intact.

5. TIMER blinks for 10 seconds and

● TIMER has been pressed when there

Check the programmed data and re-

the timer mode is disengaged.

are no programs in memory, or the

program as necessary, then press

timer record program information

TIMER again.

has not been programmed correctly.

6.

The cassette is automatically

● The end of tape was reached during

The program may not have been

ejected, the power shuts off and

timer recording.

recorded in its entirety. Next time

TIMER and ] won’t stop

make sure you have enough time on

blinking.

the tape to record the entire program.

7. Cable channels are not automatically

● The Controller is not properly

Connect the Controller correctly

switched during timer recording.

connected to the VCR.

(☞ pg. 17).

● The output channel selected in the

After confirming your cable box’s

Cable Box Output screen is incorrect.

output channel number, re-access the

Cable Box Output screen and select

the correct number (☞ pg. 18).

● The cable box’s power is off.

Make sure the power is on before

timer recording starts.

CONTINUED ON NEXT PAGE

Image 61

Contents HR-S5400U Do not place the VCR Dear CustomerImportant Product Safety Instructions Should be moved with care. Quick Product and cart combinationContents Connections Video TV OUT ANTENNA-INVideo Plug & Play Plug & Play SetupEN I Nitial Sett Ings Auto Clock Set/Auto Tuner SetInformation Language Turn on the TV and select the VCR channel 3 or 4 or AV modeClock Access Select Screens Select ModeEN Initial Settings Select Host ChannelSelect Time Zone Select D.S.T. ModeMake Corrections ManualTuner Information Access AFC Screen Access Tuner SET ScreenInitial Settings Make SelectionSituate Controller Cable Box ControlAttach Controller Connect Cable BOX to VCRSet Cable Box Output Channel Return to VCR PLUS+ SET-UP ScreenTurn on Cable BOX Access Cable BOXBrand SET Screen Return to NormalVCR Plus+ Guide Channel Matching VCR Plus+ SetupSET Screen Access Custom SETInput Guide Channel NumberConnect DBS Receiver to VCR DBS Receiver ControlDBS receiver Antenna AudioReturn to Custom SET Screen Select DBS Receiver Output ChannelSet DBS Receiver Output Channel Enter DBS Receiver Brand Turn on DBS ReceiverSet DBS Receiver Brand Brand CodeLoad a Cassette Simple PlaybackFind Program Start Point Start PlaybackSimple Recording Playback and Recording FEA Tures E N Playback FeaturesVariable-Speed Search/ Reverse Motion Playback Still Picture/Frame-By- Frame PlaybackAdjust Manual Tracking Engage Manual Tracking ModeActivate HIGH-SPEED SearchVideo Stabilizer Access Superimpose Access Function SETSuperimpose Access Audio Monitor Access Audio SelectSelect The Soundtrack MixStart Search Access Distant CodeSkip Over Unwanted Sections Stop Repeat Start RepeatActivate Counter MemoryMake Connection Access SpecialFunction Screen AV Compu Link PlaybackPerform AV Compu Link Playback Enable AV Compu Link PlaybackExample Active Video Calibration Access VideoCalibration Screen PreparationRecording PlaybackRecording Features VHS Super VHS and VHS Access S-VHS ModeStereo And SAP Second Audio Program Access 2ND AudioTo Record SAP Programs To Record Stereo ProgramsPress CH 5 or Shuttle Plus %Þ to move Hi-Fi Audio Recording Level ControlArrow to Manual by Pressing CH 5 or Audio level meters. Set the level so that maximumEN Timer Recording VCR Plus+ Timer ProgrammingPress just once to access the Auto Timer screen Engage Timer ModePress TIMER. The VCR turns off automatically CHECK/CORRECT Input DataAccess ON-SCREEN On-Screen Timer ProgrammingAccess Program SET MenuBlinking. Then set as in step PLUSÞÞuntil the item you want to change beginsOn the VCR CatvAccess Main Menu Screen Disengage TimerAccess Program SET Screen Cancel a ProgramAuto Timer Access Auto TimerMove the highlight bar arrow to Auto Timer by Now skip to of the procedure belowEngage ITR Mode Instant TimerSET Recording DurationEdit To Or From Another Audio Video Edit From a CamcorderVideo OUT Audio OUT Edit Tape DUB Mode Access AUX InputReturn to Function Reset the Counter SET Input ModeLocate END Point Locate Start PointStart Editing Engage Insert EditingEND Insert Editing Engage Audio Dubbing Audio Dubbing recorderStart Dubbing END Audio DubbingInformation on J Terminal E N Terminal JLIPJoint Level Interface Protocol ConnectorTerminal Turn on the TV TV Multi-Brand Remote ControlSET TV Brand Code Operate TVTurn on the Cable BOX Cable Box Multi-Brand Remote ControlEnter Cable BOX Brand Operate Cable BOXDBS Receiver Multi-Brand Remote Control EN Special FeaturesTurn on the DBS Receiver Operate DBS ReceiverSET Remote Control Unplug Vcrs PowerPlug in Power Cord Turn VCR Power onCassette gets stuck partway Set the switch to the positionRecording Timer againProcedure pg Re-perform the VCR Plus+ setupOubleshooting Doesn’t work properlyPlayback Questions and Answer S E NList Of Terms MBR Multi-Brand Remote Code SettingIndex Select DBS Receiver Output ChannelFront View Rear View How To Use Remote ControlYear programmable timer EIA monochrome signal20C to 60C -4F to140F Maximum recording timeFor Servicing Only in U.S.A. E N HOW to Locate Your JVC Service CenterLimited Warranty Warranty Only in U.S.AMemo HR-S5400U

HR-S5400U specifications

The JVC HR-S5400U is a pioneering VHS home video recorder that offers a myriad of features tailored to enhance the viewing experience for its users. Launched in the 1990s, this model embodies the technological advancements of its time, making it a standout choice for anyone looking to capture and playback their favorite video content.

One of the main features of the HR-S5400U is its Super VHS (S-VHS) capability, which provides superior picture quality compared to standard VHS. This technology allows for enhanced resolution and clarity, making it ideal for users who demand high-quality video playback. Additionally, the recorder supports the S-VHS ET (Extended Technology) format, enabling users to play back standard VHS tapes with improved image quality. This versatility ensures that users can enjoy their entire collection of videos without compromising on quality.

The JVC HR-S5400U is equipped with an advanced multi-head system that contributes to exceptional video performance. With its enhanced 4-head technology, the recorder delivers smoother playback and better tracking capabilities. This feature minimizes tape wear and ensures consistent quality over time, allowing users to watch their cherished memories without worrying about deterioration.

Another significant characteristic of this model is its built-in Linear Audio System, which supports high-fidelity sound quality. The double-speed audio playback ensures that audio tracks maintain their clarity and richness, enhancing the overall multimedia experience. Additionally, the HR-S5400U is designed with a variety of playback features, including slow motion, frame-by-frame advance, and a programmable timer for recording schedules, making it user-friendly and convenient.

On the connectivity front, the HR-S5400U includes multiple composite outputs, making it easy to connect to televisions and other audio-visual equipment. It also features a dedicated S-video output, which maximizes the video quality when connected to compatible devices.

In summary, the JVC HR-S5400U is a remarkable VHS recorder that combines quality, versatility, and user-friendly features. With its S-VHS capability, advanced multi-head technology, and superior audio system, it remains a notable option for enthusiasts of vintage video recording and playback systems. Whether for preserving memories or enjoying classic films, the HR-S5400U offers a solid performance that continues to be appreciated by users today.