JVC HR-S5980AJ, HR-S5980AH, LPT0800-001B specifications Timer Recording, Guide Program Number Set

[0-9] OR [R/T]: SELECT

[MENU] : EXIT

Timer Recording

Up to 8 timer recording programs can be made using G-CODE/

SHOWVIEW timer programing or Express timer programing method as far as a year in advance. Remember, the clock must be set before you can program the timer.

NOTES:

● If all the 8 programs have already been set, “PROGRAM FULL”

appears on the TV screen.

● After timer recording is completed, the recorder turns off

automatically.

● You can program the timer recording while a regular recording

is in progress; the menu screens will not be recorded.

G-CODETM/SHOWVIEWTMTimer Programming

Before performing G-CODE/SHOWVIEWTimer Programming:

●Be sure to read “G-CODETM/SHOWVIEWTMSystem Setup” ( 10).

●Insert a cassette with the safety tab in place. The recorder will come on automatically.

●Turn on the TV and select the VIDEO channel (or AV mode).

●Select the appropriate colour system ( 15).

With the G-CODEsystem , timer programming is greatly simplified because each TV programme has a corresponding code number which your recorder is able to recognise.

● In case of a power failure after programming, the recorder’s

memory backup keeps your selections (if the lithium battery is

not exhausted).

G-CODETM/SHOWVIEWTMSystem Setup

INFORMATION

G-CODEand SHOWVIEW are different trademarks used to represent the same easy recording feature, but only the term G-CODEsystem will be used in the instructions. If you use the SHOWVIEW system, follow the same instructions listed for the G-CODEsystem.

The G-CODEtimer programming system eliminates the need to input channel, date, start and stop time data when setting the

AAccess G-CODE/SHOWVIEW NO.

screen

Press PROG.

BEnter G-CODEnumber

Press the number keys to enter the G-CODEnumber of a programme you wish to record.

●If you make a mistake, press & and input the correct number.

G-CODE/SHOWVIEW NO.

[0-9]

[+/–] : EXPRESS PROGRAMING

[PROG] : EXIT

G-CODE/SHOWVIEW NO.

1 2 3 4 5 6 7 8

[0-9] [&] : DELETE [PROG] : EXIT

timer record function. Simply key in the G-CODEnumber for the TV programme you wish to record (found in most TV listings) and the recorder's timer is automatically programmed.

You have to set “GUIDE PROG” numbers, which are assigned to each station for purposes of G-CODEtimer programming, for all the stations stored in your recorder’s memory to get proper results.

Before G-CODEsetup you must have performed the procedures of Tuner Set and Clock Set.

IMPORTANT

Perform the following procedure after Auto Set Up and/or the channel setting steps.

After setting the Guide Program Numbers, channel positions may be incorrect if you stored or skipped channels. In this case, re- perform Guide Program Number setting.

Guide Program Number Set

C Enter G-CODEprogramme screen		START	– PI –
Press OK, and the G-CODEProgramme					STOP
	NO. 123456789
screen appears. (If you're just starting
		21:00			22:00
out, “P1” appears.)					SP
		DATE			TV PROG
		25.04				1
		: OK		[1] : TITLE

IMPORTANT

Make sure the channel position number you wish to record is displayed; if not, see “G-CODETM/SHOWVIEWTMSystem Setup” on page 10 and set the Guide Program number for that G-CODEnumber correctly.

●If the number you entered is invalid, “ERROR” appears on the screen. Press & and input a valid G-CODEnumber.

●If the “G-CODE/SHOWVIEW SETUP” screen appears, see “ATTENTION – Regarding Guide Program Number Set” on page 11.

AAccess Main Menu screen, then Initial Set screen

Press MENU on the remote control. Press PUSH JOG rt to place the pointer next to “INITIAL SET”, then press OK or PUSH JOG e.

BAccess G-CODE/SHOWVIEWSetup screen

Press PUSH JOG rt to place the pointer next to “G-CODE/ SHOWVIEW SETUP”, then press OK or PUSH JOG e.

C Input Guide Prog number	G-CODE/SHOWVIEW SETUP
Press PUSH JOG rt or the Number	GUIDE PROG	TV PROG
keys to select the Guide Program
	2	5
number as shown in the TV listing, then
press OK or PUSH JOG e.
	[0-9] OR [R/T]: SELECT
	[MENU] : EXIT
D Input receiving channel number	G-CODE/SHOWVIEW SETUP
Press PUSH JOG rt or the Number	GUIDE PROG	TV PROG
keys to select the number of the channel
	2	2

on which the Guide Program number’s broadcasts are received, then press OK or PUSH JOG e.

●If the satellite broadcast is received on

your recorder's auxiliary channel (“L-1” or “F-1”), select “L-1” or “F-1” for the channel position to which the satellite receiver is connected.

●Repeat steps 3 and 4 as necessary.

EReturn to normal screen

DSet tape speed

Press p to set the tape speed.

E Access title edit screen		– P1 –
Press the number keys “1”. The Title Edit
screen appears.
	25.04	21:00 PR.1

●You can access the Title Edit screen

only when “PROG. NAVIGATION” is	[0-9] : SELECT LETTERS
	[&] : DELETE
set to “ON”. ( 15)	[Y/U] : CURSOR
		: OK	[PROG] : EXIT
F Enter programme title			– P1 –
Press the number keys and PUSH JOG e
to enter characters, then press OK. For
		25.04	W
details, refer to “Entering Character” on
page 14.	[0-9] : SELECT LETTERS
	[&] : DELETE
G Return to normal screen	[Y/U] : CURSOR
		: OK	[PROG] : EXIT

Press PROG or OK. “PROGRAM

COMPLETED” appears on the screen for about 5 seconds, then normal screen appears. If “PROGRAM OVERLAPPED” appears on the screen and “Err” on the display panel, see page 13.

●Repeat steps 1 – 7 for each additional programme.

HEngage recorder’s timer mode

Press #. The recorder turns off automatically and “#” appears on the display panel.

●To disengage the timer, press # again.

Press MENU on the remote control.

— 10 —