JVC LPT0800-001B, HR-S5980AH, HR-S5980AJ Initial Settings, Video Channel Set, Auto Set Up

AUTO CH SET PLEASE WAIT

Initial Settings

Video Channel Set

Video channel (RF output channel) is the channel on which your TV receives picture and sound signals from the recorder through the RF cable. Before performing the following steps, make sure the recorder’s power is off and there is no cassette inserted in the recorder.

If you have connected the video recorder to your TV via the

provided RF cable only (RF connection)...

AHold down 0 on the

recorder until the display panel shows the following.

BPress PR + or – on the

remote control to set appropriate TV system that matches the system of TV

being used (refer to the table below). 1:B/G 2:D/K 3:I 4:H 5:M

Major Countries/Areas	TV System
New Zealand, Kuwait, U.A.E., Indonesia,
Singapore, Thailand, Malaysia, Iran, Saudi	B/G
Arabia, Egypt, Morocco, Lebanon, Iraq
China, Mongolia, Russia	D/K
Hong Kong	I
Australia	H
U.S.A., Japan, S.Korea, Taiwan	M

CSet your TV to UHF channel 36.

● If the two vertical white bars appear clearly on

the screen as shown on the right, press OK and

then go to step D.

● If the two vertical white bars do not appear clearly,

Auto Set Up

The Auto Set Up function simplifies installation by guiding you through the procedures of setting the language, clock and tuner channels — simply follow the on-screen menus that appear.

Before starting, make sure of the following:

●The TV aerial cable should be connected to the recorder.

●The recorder's mains power cord should be connected to a mains outlet. ( 4)

●The “Video Channel Set” procedure should be done first and

the TV should be set to its AV mode (with AV or S-VIDEO connection ( 4)) or video channel (with RF connection ( 4)).

IMPORTANT

●Don't press any buttons on the recorder or remote that are not directly related to the step you are performing while Auto Set Up is in progress.

●If you perform Auto Set Up successfully during installation, there's no need to separately perform the Language Select, Clock Set or Channel Set procedures, but if adjustments

become necessary they can be performed as follows: –To change the selected language ( 6)

–To reset or adjust the time ( 6)

–To add/delete channels manually ( 18)

–To reset the tuner after moving to a different location ( 18)

ASelect language

Press PUSH JOG rt to place the pointer next to your desired language (English or Chinese), then press OK or PUSH JOG e.

●The Clock Set screen appears.

B Set time

Press PUSH JOG rt to set the time, then press OK or PUSH JOG e.

●Press and hold either button to delay or advance the time by 30 minutes.

press OK and then PR + or – to set the recorder to a vacant channel

between 28 and 60 which is not occupied by any local station in

C Set date

[R/T]

your area.

(Ex.) If channel 50 is available in your area...

Then set your TV to UHF channel 50 and check if the two vertical

white bars appear clearly on the screen; if so, go to step D. If not,

re-set the recorder to another vacant channel and try again.

DPress OK to finish video channel set.

If you have connected the video recorder to your TV via both the provided RF cable and an AV cable (AV connection) or via the provided RF cable, the provided S-Video cable and an Audio cable (S-VIDEO connection)...

AHold down 0 on the

recorder until the display panel shows the following.

Press PUSH JOG rt to set the date, then press OK or PUSH JOG e.

●Press and hold either button to change the date by 15 days.

DSet year

Press PUSH JOG rt to set the year, then press MENU.

ESelect TV system

Press PUSH JOG rt to place the pointer next to the appropriate TV system (refer to the table on the left).

FStart auto channel set

Press OK or PUSH JOG e.

● Receivable channels in your area are automatically assigned to the PR +/–

buttons, and non-receivable channels STARTFINISH

until the display panel

are skipped.

■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ – – – – – – –

shows the following. Now the video channel is set to off (– –).

CPress OK to finish video channel set.

●If Auto Set Up or Tuner Set has not previously been performed, the Language Select screen appears and Auto Set Up function takes place automatically.

●When Auto Set Up is completed, the

lowest position number will appear on the front display panel. If “SCAN COMPLETED–NO SIGNAL–” is displayed on the screen, make sure that the aerial cable is connected to the recorder properly and press OK on the remote control. The recorder will try Auto Set Up again.

— 5 —