JVC HR-S8009UM manual Timer Recording, Express Timer Programing

– Timer Recording –

Timer Recording

Up to 8 timer recording programs can be made using Express timer programing method as far as a year in advance. Remember, the clock must be set before you can program the timer.

NOTES:

● If all the 8 programs have already been set, “PROGRAM FULL”

appears on the TV screen.

● After timer recording is completed, the VCR turns off

automatically.

● You can program the timer recording while a regular recording

is in progress; the menu screens will not be recorded.

● To timer-record cable channels, be sure to keep the cable box

turned on with the correct channel selected.

● In case of a power failure after programming, the VCR’s memory

backup keeps your selections (if the lithium battery is not

exhausted).

● If the tape reaches its end during timer recording, the recording

To use the VCR while it is in timer recording standby mode

Press #, then press 1. After you use the VCR, press # again to put the VCR into timer recording standby mode.

Checking, canceling or changing program settings

ADisengage timer

Press #, then press 1.

●When “AUTO TIMER” ( pg. 12) is set to “ON”, you do not have to press #.

stops and “ #“, “ ” and “ $” on the display panel blink. Press

#to disengage timer, then press STOP/EJECT (0) on the

VCR to eject the cassette or press POWER 1 then press REW

(3) to rewind the tape.

Express Timer Programing

Load a cassette with the record safety tab intact. The VCR turns on, and the counter is reset, automatically.

BAccess Program Check screen

Press " (CHECK).

CAccess Program screen

Press " (CHECK) again. Each time you press " (CHECK), the next program’s Program screen appears.

PR START		STOP	CH	DATE
1	8:00P	10:00	12	12/24
2	10:00A	10:45	40	12/25
3	11:30P	1:00	125	12/25
4
5
6
7
8
	PRESS (CHECK) TO NEXT
	PROGRAM 1
	START		STOP
	8:00 PM		10:00 PM
	DATE		CH
	12/24/02		12	SP

PRESS (CANCEL) TO CANCEL PRESS (CHECK) TO NEXT

APress PROG on the Remote to access the Program screen.

B Press START+/–,STOP+/–,DATE+/–		PROGRAM 1
or PR+/– repeatedly to enter the start		START	STOP
time, stop time, date or channel.		– –:– –AM	– –:– –AM
		DATE	CH
● Press and hold START+/– or
		– –/– –/– –	– – –	SP
STOP+/– to increase the time in
	PRESS (+/–, SP/EP, 8=DAILY
30-minute intervals.	9=WEEKLY), THEN (0K)
● To set the tape speed, press SP/EP	PRESS (PROG.) TO END

(p).

● To timer-record daily (Monday–Friday) or weekly serials, press DAILY (M-F) (Number key “8”) or WEEKLY (Number key “9”). Pressing the button again makes the “DAILY” or “WEEKLY” display disappear.

CPress OK or PROG.

●If “PROGRAM NOT COMPLETED PROGRAM OVERLAP” appears, see “Program overlap warning display” ( pg. 11).

DPress #. The VCR turns off automatically and “#” is displayed on the display panel.

DCancel or change program setting

To cancel a program, press & (CANCEL) when the Program screen you do not want is shown.

To change a program, press the appropriate button: START+/–, STOP+/–, DATE+/–, PR+/–, DAILY (M-F) (Number key “8”), WEEKLY (Number key “9”) and/or SP/EP (p) when the Program screen on which you want to make changes is shown.

EReturn to normal screen

Press " (CHECK) repeatedly until no Program screen is shown.

FReengage timer recording standby mode

Press #. The VCR turns off automatically and “#” is displayed on the display panel.

●When “AUTO TIMER” ( pg. 12) is set to “ON”, the timer recording standby mode automatically resumes when you turn off the VCR.

— 10 —