JVC HR-VP675U manual Turn on the DBS Receiver, Enter DBS Receiver Brand, Operate DBS Receiver

Page 50

50ENSPECIALFEATURES(CONT.)

BR SET

DBS Receiver Multi-Brand Remote Control

The VCR's remote control can control functions on the brands of DBS (Direct Broadcast Satellite) receivers listed below.

CABLE/DBS

POWER

TURN ON THE DBS RECEIVER

	1		2	3
		ENTER			2
	4	ENTER	5	6	NUMBER
					NUMBER

	7		8	9
			0		4

1

STOP

3

TV CH+/–

1 Turn the power on using the DBS receiver's remote control.

ENTER DBS RECEIVER

BRAND

2 While holding down CABLE/DBS on the VCR’s remote control, press MBR SET and use the NUMBER keys to enter the DBS receiver brand number from the chart in the left column and then press STOP.

Follow the example shown below.

Check if the DBS receiver's power goes off as it should. If it does, try other operations (☞ step 3).

●Once you have set the remote control to operate the DBS receiver, you don't have to repeat this step until you replace the remote control's batteries.

OPERATE DBS RECEIVER

3 First, while holding down CABLE/DBS, press the corresponding button: POWER, TV CH +/–, NUMBER keys.

●Depending on the DBS receiver you may have to press ENTER after having pressed the NUMBER keys.

●To change the DBS receiver's channel, press TV CH +/– or the NUMBER keys. (The CH +/– button can be used to change the VCR's channel only.)

NOTES:

●Depending on the type of DBS receiver, there may be cases where some or all functions cannot be operated using the remote control.

●It's not possible to operate a DBS receiver that is not equipped with a remote control sensor.

●Though ECHOSTAR has a number of different remote codes, this remote control is applicable only to one of those codes preset at the factory.

●It's not possible to set the remote control for both your DBS receiver and a cable box at the same time. You can only set the remote control to operate one of these units at a time.

DBS BRAND NAME	BRAND CODE

JVC (DISH Network)	51
ECHOSTAR (DISH Network)	51
PRIMESTAR	50
SONY (DSS)	41
RCA (DSS)	40

(Ex.) To set remote control to JVC 51:

CABLE/	MBR SET
DBS	A/B
	5	1	STOP
	5	1

	Hold	Press in succession
	down	Press in succession
	down

Release

Image 50

Contents HR-VP675U Dear Customer Do not place the VCRPower Lines Power SourcesPower Cord Protection Grounding or PolarizationCleaning AccessoriesDamage Requiring Service Replacement PartsContents Back of VCR EN Installing Your NEW VCRBasic Connections Matching Transformer not suppliedSituate VCR Check ContentsConnect VCR to Power Source Connect VCR to TVEN I Nitial Sett Ings Plug & Play SetupPlug & Play Auto Clock Set/Auto Tuner SetInformation Language Preparation Access Clock SETClock Shuttle PLUS%Þ, then Press OK or ShuttleSelect Host Channel Select D.S.T. ModeSET Auto Clock to on Semi-AutoSET Date Select Time ZoneReturn to Normal Screen SET YearTuner Access Main Menu ScreenAccess Tuner SET Screen SETChannel Access Manual Channel SET ScreenADD or Skip Desired Add Or Delete a ChannelAttach Controller Cable Box ControlSituate Controller Connect Cable BOX to VCRSet Cable Box Output Channel & Cable Box Brand Access Cable BOX SETTurn on Cable BOX Plus %Access Cable BOX Brand SET Screen Enter Cable BOX BrandConnect DBS Receiver To VCR Fasten securely using the supplied adhesive stripsDBS Receiver Control DBS receiverOutput Channel Turn on DBS ReceiverSelect DBS Receiver Set DBS Receiver Output Channel & DBS Receiver BrandAccess DBS Receiver Simple Playback Simple Recording Frame Playback Playback FeaturesActivate FRAME-BY Adjust Manual Tracking Access Distant CodeEngage Manual Tracking Mode Activate HIGH-SPEED SearchLayback and Recording Features Access Function SETSET Mode Picture ControlSelect The Soundtrack Video StabilizerStart Repeat Stop RepeatSuperimpose Access Function SET ScreenSelect Superimpose SET Mode Advance Access Skip MenuPerform Movie Movie AdvanceOK or Shuttle Plus % AV Compu Link PlaybackExample PLUS%to set to onActive Video Calibration Playback RecordingSelect Channel for Viewing Recording FeaturesEngage TV Mode Record One Program While Watching AnotherStereo And SAP Second Audio Program To Record SAP ProgramsNumber VCR Plus+ Timer ProgrammingEN Timer Recording Tion is displayed on Engage Timer ModeEntered and the matching Make sure it’s accuratePLUS%Þ to move VCR Plus+ SetupVCR Plus+ Guide Channel Matching Initial SET, then pressInput Receiving Channel Number Access Guide Channel SET ScreenInput Guide Channel Press CH5, ShuttleSET Channel Number Express Timer ProgrammingSET Program Date Screen appears Press SP/EP to set the tape speedPress PROG. or OK. Program Completed Is displayed on the display panelPress TIMER, then press Power RE-ENGAGE TimerCheck, Cancel And Revise Programs ProgramAuto Timer Select Auto SP EP Timer SET ModeAuto SP→EP Timer SET Recording Duration Instant Timer Recording ITREngage ITR Mode Press REC on the front panelEdit To Or From Another Edit From a Camcorder EditingEnable Remote Pause Function Turn on the TV EN Special FeaturesTV Multi-Brand Remote Control SET TV Brand CodeOperate Cable BOX Cable Box Multi-Brand Remote ControlTurn on the Cable BOX Turn on the DBS Receiver EN S P Ecial FeaturesDBS Receiver Multi-Brand Remote Control Enter DBS Receiver BrandPlug in Power Cord Unplug Vcrs PowerSET Remote Control Turn VCR Power onTroubleshooting Cassette gets stuck partwayProcedure pg Those in the previous area Timer againRe-perform the VCR Plus+ setup Doesn’t work properly Has not been programmed correctly Cassette is automaticallyOther Problems RoubleshootingCan the VCR indefinitely remain in the Record-Pause mode? Quest Ions and Answers ENCan the VCR indefinitely remain in the still mode? What happens if the tape runs out during recording?Index Express Timer ProgrammingMBR Multi-Brand Remote Code Setting List Of TermsFront View EN Index Rear ViewRemote Control Year programmable timer 20C to 60C -4F to140FHOW to Locate Your JVC Service Center For S Ervicing Only in U.S.AWarranty Only in U.S.A Limited WarrantyMemo HR-VP675U