JVC SR-VS20U manual Access DBS Receiver, DBS Receiver Code from Following list, then Press OK, Jvc

Page 20

20ENINITIALSETTINGS(cont.)

T	2	W
1	2	3

2

4 5 6

NUMBER

7 8 9

0 4

1

DV

S-VHS

3

OK

	ACCESS DBS RECEIVER
	BRAND SET SCREEN
7 Press OK.
	SET DBS RECEIVER BRAND
	Press the appropriate		DBS RECEIVER BRAND SET
	NUMBER keys to enter the		DBS RECEIVER BRAND SET
	NUMBER keys to enter the
8 DBS Receiver Code from
					4 0

	the following list, then
	press OK.

			PRESS NUMBER KEY (0–9)
			THEN (OK) TO TEST
			PRESS (MENU) TO END


	BRAND				CODE
	JVC (DISH Network)			51
	ECHOSTAR (DISH Network)			51
	PRIMESTAR			50
	SONY (DSS)			41
	RCA (DSS)			40

●After OK is pressed, the program currently received through the DBS receiver will appear for about 10 seconds.

●If the DBS receiver's channel changes to the channel listed below for your brand of DBS receiver, setting is complete. Press OK and "DBS RECEIVER CONTROL IS ON" appears on the screen for about 5 seconds, then it returns to the normal screen.

JVC [ 100

ECHOSTAR [ 100

PRIMESTAR [ 55

SONY [ 205

RCA [205

●If the DBS receiver's channel does not change as shown above, press %Þ to move the highlight bar (arrow) to "NO", then press OK. Re-enter the correct code.

NOTES:

●It is possible that the Controller will not work with all types of DBS receiver.

●If your DBS receiver doesn’t respond to the code, you can’t use the Controller to change satellite channels. In this case, make sure to leave the DBS receiver turned on and tuned to the proper channel before the scheduled start of timer recording.

●The VCR can only change the satellite channel through the Controller during timer recording.

●If your DBS receiver is one that can’t be operated with a remote control (because it has no remote sensor), you can’t use the Controller to change its channels. Make sure to leave the DBS receiver turned on and tuned to the proper channel before the scheduled start of timer recording.

●If you are unable to set the Controller, please contact JVC toll free at 1-800-537-5722.

Image 20

Contents SR-VS20U Dear Customer Do not place the VCRInstallation Antenna Installation InstructionsServicing Before YOU Install Your NEW VCRUSE Contents Connections Connect VCR to TV Back of VCRAudio/Video Cable supplied RF Cable suppliedPlug & Play Setup Plug & PlayEN I Nitial Sett Ings Auto Clock Set/Auto Tuner SetLanguage Access Main Menu Screen Access Initial SET ScreenAccess Clock SET Screen EN Initial SettingsSemi-Auto SET Auto Clock to onSelect Host Channel Select D.S.T. Mode Select Time ZoneReturn to Normal Screen SET TimeAccess Tuner SET Screen TunerSET Set Receivable ChannelsAccess Main Menu Screen Access Manual Channel SETAdd Or Delete a Channel ScreenCable Box Control Situate ControllerAttach Controller Connect Cable BOX to VCRAccess Cable BOX SET Screen Turn on Cable BOXSelect Cable BOX Output Channel Set Cable Box Output Channel & Cable Box Brand Brand Code Access Cable BOX Brand SET Screen Enter Cable BOX Brand DBS receiver DBS Receiver ControlConnect DBS Receiver to VCR Turn on DBS Receiver Select DBS ReceiverSet DBS Receiver Output Channel & DBS Receiver Brand On NextAccess DBS Receiver DBS Receiver Code from Following list, then Press OKJVC Dish Network Echostar Dish Network JVCSimple Playback Simple Recording Select DV Deck DV DeckPlayback Features Pause During PlaybackActivate FRAME-BY Frame Playback Activate SLOW-MOTIONActivate HIGH-SPEED Search Variable-Speed Search/ Reverse Motion PlaybackStill Picture/Frame-By-Frame Slow Motion/Reverse SlowEngage Manual Tracking Mode Adjust Manual TrackingAccess Distant Code RE-ENGAGE Automatic TrackingAccess Mode SET Screen ModeSuperimpose Select Superimpose SETStart Repeat Stop RepeatPicture Control VHS deck only Access VHS Mode SETSET Mode Video Stabilizer Access VHS Mode SET Screen Select Digital TBC/NR SET ModeDigital TBC/NR VHS deck only Digital R3 VHS deck onlyOn the remote control Select The SoundtrackOn the Screen VHS deckAccess DV Mode SET Screen Access DV Mode SETSelect 12BIT Mode Sound Mode SelectionVideo Calibration Active Video CalibrationVHS deck only Recording Recording Features Select 2ND Audio Record SET Mode Engage RECORD-PAUSE ModeLocate Start Point Resume RecordingET and VHS VHS deck only Select S-VHS ModeVHS Super VHS, S-VHS Engage S-VHS ET Mode Super VHS ET VHS deck onlyVCR Plus+ Timer Programming EN Timer RecordingPress PROG. on the remote control Enter Pluscode NumberCheck Program Data Engage Timer ModeInput Receiving Channel Number Initial SET, then press Changing VCR Plus+ SettingVCR Plus+ Guide Channel Matching Number Access Guide Channel SET ScreenInput Guide Channel Express Timer SET Program Stop TimeSET Program Date SET Channel NumberPower Access Program Check Screen Access Program ScreenCheck, Cancel And Revise Programs ProgramCancel or Change Programme Setting Confirm OverlappingProgrammes Select Programme toTimer SET Mode Timer RecordingAuto SP→EP Timer Auto TimerInstant Timer Engage ITR ModeSET Recording Duration Recording Resume FunctionTape Dubbing Load CassettesSelect Dubbing DirectionNormal DubbingPause Dubbing END DubbingPause Random Assemble EditingProgram Editing Memory 8 programmes x 8 scenes RECORD-PAUSE Mode Prepare Source TapeEngage VHS Deck to Start EditingMake Connections Load a CassetteRecorder PlayerSET RECORDER’S Input Mode Control SET ModeSelect Front AUX Input SET ModeEditing Edit To Or From AnotherMake Connections SET RECORDER’S Input Mode OUTPUT1 SettingSelect Edit for PIC Start PlayerSET Input Mode Audio DubbingVHS Audio Dubbing DV Audio DubbingEND Audio Dubbing DV Insert Editing SP Mode Only Insert EditingLocate END Point VHS Deck onlyEngage Insert Editing Start EditingEND Insert Editing For AV Insert Editing VHS deck onlyConnecting To a Video Titler Connecting To a Printer Digital printerSET Remote Control Mode Turn on the TVSET TV Brand Code Operate TVCable Box Multi-Brand Remote Control Turn on the Cable BOXOperate Cable BOX Cable BOX Brand Name Brand CodeSET Remote Control Special FeaturesDBS Receiver Multi-Brand Remote Control Turn on the DBSUnplug Vcrs Power Plug in Power CordTurn VCR Power on CordClear or USE Cleaning Dealer Cassette gets stuck partwayThen insert the cassette Recording won’t startRe-perform the set-up procedures Timer againPoint is not dubbed That ä appears on the front display PanelRe-perform the VCR Plus+ setup Procedure pgRoubleshooting Plus+ system doesn’t work properlyQuest Ions and Answers EN Can the VCR indefinitely remain in the still mode?Can the VCR indefinitely remain in the Record-Pause mode? What happens if the tape runs out during recording?Index Front ViewRear View Counter C. Reset Button pg Express Timer Programming Plug & Play Random Assemble Editing Record Safety TabVideo Connection Tape Dubbing Tape Position Indicator List Of TermsNTSC-type colour signal and EIA Monochrome signal, 525 lines20C to 60C -4F to 140F Frequency-synthesized tuner

Related manuals

Manual 76 pages 43.51 Kb