JVC SR-VS20U manual Engage S-VHS ET Mode, Super VHS ET VHS deck only

Page 39

Super VHS ET (VHS deck only)

Your VCR is equipped with Super VHS ET that makes it possible to record with S-VHS picture quality on VHS cassettes.

1		ENGAGE S-VHS ET MODE
		Press S-VHS ET on the VCR. You can check the current
		setting ("S-VHS ET : ON" or "S-VHS ET : OFF") if
		"SUPERIMPOSE" is set to "ON" (☞ pg. 27). If "S-VHS ET
		: OFF" appears on the TV screen, press S-VHS ET again
		in about 5 seconds to set it to "ON".

		● The S-VHS indicator lights up on the front display
		panel.

NOTES:

●You cannot activate the S-VHS ET function...

...while recording is in progress.

...while timer-recording (incl. Instant Timer Recording

☞pg. 49) is in progress.

...while Video Calibration (☞ pg. 34) is in progress.

...when the VCR's power is off.

●S-VHS ET does not work with S-VHS tapes.

EN39

S-VHS ET

This facility allows recording with S-VHS picture quality on VHS cassettes. You can play back those cassettes recorded in S-VHS ET on a VCR equipped with S-VHS ET.

NOTES:

●To obtain the highest quality recording and playback pictures over a longer period on this model, S-VHS recording on S-VHS tape is recommended.

●You can play back S-VHS ET recordings not only on this VCR but also on another VHS VCR equipped with S-VHS ET.

*It is recommended to specifically label S-VHS ET recordings so you can easily distinguish them from regular VHS recordings.

●S-VHS ET recordings can also be played back on an S- VHS VCR or a VHS VCR equipped with SQPB (S-VHS QUASI PLAYBACK) function. However, there may be cases where S-VHS ET playback is not possible on a particular VCR.

●Frequent still, frame-by-frame and slow-motion playback may damage the tape and cause picture degradation.

●With some tapes, better picture quality may not be obtained even with S-VHS ET recording. It is recom- mended that you do test record beforehand to make sure whether better results can be obtained.

●High Grade tapes are recommended for superior results.

●Make sure that "VIDEO CALIBRATION" is set to "ON" at the Function screen (☞ pg. 34).

●During S-VHS ET playback, noise may appear depending on tape quality.

●Noise may appear during still, frame-by-frame and slow- motion playback.

●If the playback picture becomes blurred or interrupted, use a cleaning cassette.

Image 39

Contents SR-VS20U Do not place the VCR Dear CustomerAntenna Installation Instructions InstallationBefore YOU Install Your NEW VCR USEServicing Contents Connections RF Cable supplied Connect VCR to TVBack of VCR Audio/Video Cable suppliedAuto Clock Set/Auto Tuner Set Plug & Play SetupPlug & Play EN I Nitial Sett IngsLanguage EN Initial Settings Access Main Menu ScreenAccess Initial SET Screen Access Clock SET ScreenSET Auto Clock to on Select Host ChannelSemi-Auto SET Time Select D.S.T. ModeSelect Time Zone Return to Normal ScreenSet Receivable Channels Access Tuner SET ScreenTuner SETScreen Access Main Menu ScreenAccess Manual Channel SET Add Or Delete a ChannelConnect Cable BOX to VCR Cable Box ControlSituate Controller Attach ControllerSet Cable Box Output Channel & Cable Box Brand Access Cable BOX SET ScreenTurn on Cable BOX Select Cable BOX Output ChannelAccess Cable BOX Brand SET Screen Enter Cable BOX BrandBrand Code DBS Receiver Control Connect DBS Receiver to VCRDBS receiver On Next Turn on DBS ReceiverSelect DBS Receiver Set DBS Receiver Output Channel & DBS Receiver BrandJVC Access DBS ReceiverDBS Receiver Code from Following list, then Press OK JVC Dish Network Echostar Dish NetworkSimple Playback Simple Recording DV Deck Select DV DeckActivate SLOW-MOTION Playback FeaturesPause During Playback Activate FRAME-BY Frame PlaybackSlow Motion/Reverse Slow Activate HIGH-SPEED SearchVariable-Speed Search/ Reverse Motion Playback Still Picture/Frame-By-FrameRE-ENGAGE Automatic Tracking Engage Manual Tracking ModeAdjust Manual Tracking Access Distant CodeSelect Superimpose SET Access Mode SET ScreenMode SuperimposeStop Repeat Start RepeatAccess VHS Mode SET SET ModePicture Control VHS deck only Video Stabilizer Digital R3 VHS deck only Access VHS Mode SET ScreenSelect Digital TBC/NR SET Mode Digital TBC/NR VHS deck onlyVHS deck On the remote controlSelect The Soundtrack On the ScreenSound Mode Selection Access DV Mode SET ScreenAccess DV Mode SET Select 12BIT ModeActive Video Calibration VHS deck onlyVideo Calibration Recording Recording Features Resume Recording Select 2ND Audio Record SET ModeEngage RECORD-PAUSE Mode Locate Start PointSelect S-VHS Mode VHS Super VHS, S-VHSET and VHS VHS deck only Super VHS ET VHS deck only Engage S-VHS ET ModeEnter Pluscode Number VCR Plus+ Timer ProgrammingEN Timer Recording Press PROG. on the remote controlEngage Timer Mode Input Receiving Channel NumberCheck Program Data Changing VCR Plus+ Setting VCR Plus+ Guide Channel MatchingInitial SET, then press Access Guide Channel SET Screen Input Guide ChannelNumber SET Channel Number Express TimerSET Program Stop Time SET Program DatePower Program Access Program Check ScreenAccess Program Screen Check, Cancel And Revise ProgramsSelect Programme to Cancel or Change Programme SettingConfirm Overlapping ProgrammesAuto Timer Timer SET ModeTimer Recording Auto SP→EP TimerRecording Resume Function Instant TimerEngage ITR Mode SET Recording DurationDirection Tape DubbingLoad Cassettes Select DubbingEND Dubbing NormalDubbing Pause DubbingRandom Assemble Editing Program Editing Memory 8 programmes x 8 scenesPause Start Editing RECORD-PAUSE ModePrepare Source Tape Engage VHS Deck toPlayer Make ConnectionsLoad a Cassette RecorderMode SET RECORDER’S Input ModeControl SET Mode Select Front AUX Input SETEdit To Or From Another Make ConnectionsEditing Start Player SET RECORDER’S Input ModeOUTPUT1 Setting Select Edit for PICDV Audio Dubbing SET Input ModeAudio Dubbing VHS Audio DubbingEND Audio Dubbing VHS Deck only DV Insert Editing SP Mode OnlyInsert Editing Locate END PointFor AV Insert Editing VHS deck only Engage Insert EditingStart Editing END Insert EditingConnecting To a Video Titler Digital printer Connecting To a PrinterOperate TV SET Remote Control ModeTurn on the TV SET TV Brand CodeCable BOX Brand Name Brand Code Cable Box Multi-Brand Remote ControlTurn on the Cable BOX Operate Cable BOXTurn on the DBS SET Remote ControlSpecial Features DBS Receiver Multi-Brand Remote ControlCord Unplug Vcrs PowerPlug in Power Cord Turn VCR Power onRecording won’t start Clear or USE Cleaning DealerCassette gets stuck partway Then insert the cassetteThat ä appears on the front display Panel Re-perform the set-up proceduresTimer again Point is not dubbedPlus+ system doesn’t work properly Re-perform the VCR Plus+ setupProcedure pg RoubleshootingWhat happens if the tape runs out during recording? Quest Ions and Answers ENCan the VCR indefinitely remain in the still mode? Can the VCR indefinitely remain in the Record-Pause mode?Front View IndexRear View Counter C. Reset Button pg List Of Terms Express Timer ProgrammingPlug & Play Random Assemble Editing Record Safety Tab Video Connection Tape Dubbing Tape Position IndicatorFrequency-synthesized tuner NTSC-type colour signal and EIAMonochrome signal, 525 lines 20C to 60C -4F to 140F

Related manuals

Manual 76 pages 43.51 Kb