JVC HR-DD740U manual DBS Receiver Control, Connect DBS Receiver to VCR, DBS receiver

Page 20

20ENINITIALSETTINGS(cont.)

DBS Receiver Control

Suggested Location

Place the DBS (Direct Broadcast Satellite) receiver on top of the VCR. Attach the VCR's Controller to the top of the VCR with the Controller’s transmitter pointed towards the DBS receiver's remote sensor.

Attention:

The Controller can also control a cable box. If both a DBS receiver and a cable box are used, position the controller so its signal reaches the remote control sensors of both the DBS receiver and cable box.

DBS receiver

Your VCR

Controller

 

(suggested locations)

 

DBS receiver

 

 

 

 

 

 

Controller

 

 

Transmitter

 

 

 

 

Connected to

Connected

 

 

 

 

 

 

to VIDEO/

 

 

ANTENNA IN

AUDIO IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Your VCR

CABLE

BOX

About Your DBS Receiver

This VCR has two separate methods to control your DBS Receiver.

The VCR's Wireless Remote Control Unit can control your DBS Receiver.

This eliminates the need for a separate DBS Receiver Remote Control Unit.

The VCR's Controller can also control your DBS Receiver. This allows the VCR to change your DBS receiver's channel number during timer recording.

Each method must be set up separately. To set up the VCR's Remote Control unit, refer to page 53. To set up the Controller go to page 21.

The following procedure is required if you receive satellite channels through a DBS (Direct Broadcast Satellite) Receiver. The Controller allows the VCR to automatically switch the DBS Receiver's channels during timer recording.

The VCR can control the DBS Receiver during timer recording using its Controller.

NOTES:

The Controller can automatically change the DBS Receiver channels when the VCR has been programmed using On- Screen Timer Programming (pg. 44).

Because satellite programming does not use PlusCode; the Controller can not change the DBS Receiver channels during VCR Plus+ Timer Recording.

If a cable box is also used it is recommended that you connect the DBS receiver to your VCR's A/V inputs and the cable box to your VCR's antenna input.

Situate And Connect Controller

SITUATE CONTROLLER

1 Place the Controller so that the path between its transmitter and the DBS receiver's remote sensor is unobstructed.

ATTACH CONTROLLER

2 Fasten securely using the supplied adhesive strips.

CONNECT DBS RECEIVER TO VCR

3 The connection method depends on the type of DBS receiver you have.

If your DBS receiver has AUDIO and VIDEO OUT connectors . . .

. . . connect them to the AUDIO and VIDEO IN connectors on your VCR; select the correct external input mode as described in step 4, 5, 9 11 on page 48

&49. Set the VCR to channel "AU" to use the DBS receiver.

If your DBS receiver doesn’t have AUDIO and VIDEO OUT connectors . . .

. . . connect the antenna output connector on the DBS receiver to the ANTENNA IN connector on the rear of your VCR.

Set the VCR's tuner to the same channel as the DBS receiver's RF output. (See page 21 also.)

NOTE:

When connecting your DBS receiver refer to its instruction manual.

CONNECT CONTROLLER TO VCR

4 Connect to the CABLE BOX connector on your VCR.

Image 20
Contents HR-DD740U Dear Customer Do not place the VCRPower Sources Power Cord ProtectionPower Lines Grounding or PolarizationAccessories Damage Requiring ServiceCleaning Replacement PartsContents Basic Connections Plug & Play Setup Initial SettingsPlug & Play Auto Clock Set/Auto Tuner SetLanguage Clock Select ScreenPreparation Time Scan %Þ, thenSelect Mode Access Select ScreensSelect Host Channel Semi-AutoSelect D.S.T. Mode Select Time ZoneSET DATE, Time and D.S.T Make CorrectionsAccess Main Menu Access Tuner SETTuner SETInformation Access Tuner SET Screen Access AFC ScreenMake Selection Store or Skip Desired ChannelCable Box Control Situate ControllerAttach Controller Connect Cable BOX to VCRAccess Custom SET Screen Access VCR PLUS+ SET-UP ScreenSelect Cable BOX Output Channel Set Cable Box Output ChannelAccess Cable BOX You can now set up the VCR Plus+ feature pgTurn on Cable BOX Brand SET ScreenVCR Plus+ Setup VCR Plus+ Guide Channel MatchingAccess Custom SET Screen Input Receiving Channel Number Access Guide Channel SET ScreenSET-UP Screen Check Input DataFasten securely using the supplied adhesive strips DBS Receiver ControlConnect DBS Receiver to VCR DBS receiverSet DBS Receiver Output Channel Press CH5 or TimeSCAN%Þ to move Highlight bar arrow toTurn on DBS Receiver Enter DBS Receiver BrandSet DBS Receiver Brand DBS Receiver Brand SET, then press OKSimple Playback Simple Recording Playback Features Pause During PlaybackActivate FRAME-BY Frame PlaybackEngage Manual Tracking Mode Adjust Manual TrackingLayback and Recording Features RE-ENGAGE Automatic TrackingVideo Stabilizer Access Function SET Access SuperimposeReturn to Normal SuperimposeAccess Audio Select Access Audio MonitorSelect The Soundtrack MixAccess Distant Code Start SearchIndex Search Instant ReViewStart Repeat Activate CounterMemory Return to Counter Position ZeroAccess Special Make ConnectionFunction Screen AV Compu Link PlaybackEnable AV Compu Link Playback ExampleAuto Picture Press Play VCR adjusts Playback picture quality PlaybackBased on the quality Tape in useVariable-Speed Search/ Reverse Motion Playback Audio signal during TimeScanTimeScan Skip Over Unwanted Sections TimeScanSkip Search Speed Audio outputAccess Timescan Audio ScreenTimeScan Audio CH or Time ScanRecording Features Engage TV ModeReset Counter to Zero Select Channel for ViewingAccess 2ND Audio Stereo And SAP Second Audio ProgramTo Record SAP Programs To Record Stereo ProgramsInstant Timer Recording ITR Engage ITR ModeTimer Recording SET Recording DurationVCR Plus+ Timer Programming EN Timer RecordingCHECK/CORRECT Input Data Engage Timer ModePress TIMER. The VCR turns off automatically Information On-Screen Timer ProgrammingAccess Program SET Cable BOX Output is set to OFF pg.16 To timer-record a regular TV program received on the VCRCatv Disengage Timer Access Main Menu ScreenAccess Program SET Screen Cancel a ProgramOr, during on-screen timer programming Access Auto TimerAuto Timer Edit From a Camcorder Make ConnectionsSET RECORDER’S Input ModeAccess AUX Input Return to FunctionSET Screen Start RecorderSET RECORDER’S Input Mode Edit To Or From AnotherLoad Cassettes Start PlayerSpecial Features TV Multi-Brand Remote ControlTurn on the TV SET TV Brand CodeEN Special Features Cable Box Multi-Brand Remote ControlTurn on the Cable BOX Enter Cable BOX BrandDBS Receiver Multi-Brand Remote Control Turn on the DBSReceiver Enter DBS ReceiverUnplug Vcrs Power SET Remote ControlPlug in Power Cord Turn VCR Power onCassette gets stuck partway Troubleshooting E NSet the switch to the position Timer again OubleshootingRe-perform the VCR Plus+ setup Doesn’t work properly When scanning channels, someEN Questions and Answers Can the VCR indefinitely remain in the still mode?Can the VCR indefinitely remain in the Record-Pause mode? What happens if the tape runs out during recording?MBR Multi-Brand Remote Code Setting IndexList Of Terms Select DBS Receiver Output ChannelFront View Rear View Installing Batteries How To UseSpecifications HOW to Locate Your JVC Service Center For Servicing Only in U.S.AWarranty Only in U.S.A Limited WarrantyEMO Memo HR-DD740U