Magnavox VRA651AT owner manual Helpful Hints

Page 54

54 Helpful Hints

If you are having problems with your VCR, check the following list of problems and possible solutions before requesting service. You may be able to solve the problem yourself.

If you need to call a customer service representative, please know the model number and serial number of your product before you call. This information is displayed on the back of the product. Also, please take a moment to identify the problem you are having, and be prepared to explain this to the representative. If you believe the representative will need to help you with operations, please stay near the product. Our representatives will be happy to assist you.

The VCR has no power.

•Make sure the power plug is completely connected to an AC (alternating current) outlet.

•Make sure the power is turned on.

A power failure occurred.

•Select a language and set up channels, if prompted to do so. Details are on pages 11-12 and 19. Reset the clock if necessary. Details are on pages 13-17.You also may need to reprogram your timer recordings. Details are on pages 32-39.

The VCR cannot be controlled with the remote control.

•Aim the remote control directly at the VCR’s remote sensor. Details are on pages 5 and 22.

•Remove all obstacles between the remote control and the VCR.

•Inspect and/or replace the batteries in the remote control. Details are on page 5.

•Press the VCR button, then try the other buttons.

The VCR does not respond normally to the remote control. (For example, the VCR may change channels multiple times when you press the CH(annel) 8 button once.)

• Install new batteries (preferably alkaline) in the remote control.

The VCR will not perform a timer recording.

•Make sure the recording start and stop times are set correctly. Details are on pages 32-39.

•Make sure there is a tape in the VCR.

•Make sure the tape has a record tab. Details are on page 5.

•Make sure the VCR power is off.

•Make sure the clock is set. Details are on pages 13-17.

•The VCR may not perform or continue a timer recording if a power interruption of more than 10 min- utes occurs, even if the power comes back on. If timer recordings are lost, - - : - - should appear on the display panel. But, even if you do not see this indication and the VCR operates normally, check pro- grammed timer recordings.

•When you turn on the VCR after a power failure, this on-screen message may appear: POWER FAILURE OCCURRED/TIMER MEMORY CLEARED (IF PROGRAMMED)/PLEASE SET PROGRAMS TO BE RECORDED/TO END PUSH EXIT. First, reset the clock. Details are on pages 13-17.Then, set up chan- nels. Details are on pages 11-12.Finally, program the timer recordings again. Details are on pages 32-39.

•Finish programming a timer recording at least five minutes before the recording is scheduled to begin.

•If the VCR power is turned off for a timer recording and there isn’t a tape in the VCR, the r and Cassette-Inside lights will blink on the display panel.

•If the record tab on a tape is missing and you turn off the VCR to set a timer recording, the VCR will eject the tape. The r and Cassette-Inside lights will blink on the display panel.

•Noon is 12 p.m.; midnight is 12 a.m.

•If you are using a Cable Box/DBS, enter the Cable Box/DBS output channel (03 or 04) at step 3 on page 36, then select the channel to be recorded at the Cable Box/DBS. Leave the Cable Box/DBS on for the timer recording.

Tape can’t be inserted.

•Insert the tape window side up, with the record tab facing you.

•Make sure a tape isn’t already in the VCR by pressing the STOP/EJECT button on the VCR or the EJECT button on the remote control.

•Gently push the center of the tape as you put it in the VCR. Never force a tape into the VCR.

Page 53 Page 55
Image 54
Page 53 Page 55
Contents VRA451 VRA651 Dear Philips Magnavox product owner For Customer UseFeatures Safety PrecautionsIntroduction Table of Contents Before Using Your VCR Hookups without a Cable Box Disconnect the antenna or cable from your TVHookups without a Cable Box cont’d CH3 CH4Connections Connect a Cable signal to the in jack on the Cable Box/DBSHookups with a Cable Box/Direct Broadcast System Recording/Viewing Any ChannelWith this connection Cable signal RF coaxialRecording One Channel/Watching Another 2Cable Box/DBSPress the VCR button, then press the Power button Turning on Your VCRBox/DBS Automatic Channel Setup Press the VCR button, then press the Menu buttonAdding/Deleting Channels Press the Play 8 or Stop 9 button to selectADD/DELETE CH., then press the FF /OK button To make corrections, follow steps Manual Clock SettingInstructions continue on ButtonPress the Play 8 or Stop 9 button repeatedly to set Setting the Clock cont’dWhen the month and day are correct, press the FF /OK ButtonTime Zone Selection Press the FF /OK button repeatedly to select TimeManual PBS Channel Selection Automatic PBS Channel Selection Press the FF /OK button repeatedly to select PBS CHDaylight-Savings Time OFF, PBS CH. and Time Zone will not appear in the menuLanguage Selection Press the Stop 9 button or Play 8 button to selectRemote Control Buttons Speed Button Timer ButtonVCR/TV Button STILL/SLOW Buttons While recording, pressDisplay Panel Front VIDEO/AUDIO OK Button Play Button Jacks STOP/EJECT Button FF Fast Forward ButtonSTILL/PAUSE Button REWind Button MENU/EXIT ButtonRear Panel VRA651If on Screen Mode is set to on or Counter On-Screen Status DisplaysSetting the Remote Control to Operate a TV TV CodesSetting the Remote Control to Operate a Cable Box/DBS Sqpb does not deliver Super VHS resolution PlayingIf playback does not start automatically, press the Play VCR records in a preset volume RecordingPress the VCR button Starting an OTR Channels are set up. Details are on pagesOne-Touch Recording OTR has priorityRecording One Channel/Watching Another VCR light will disappear from the display panelSetting Up the VCR Plus+ Programming System ChannelsCall Letters Setting Up the VCR Plus+ Programming System cont’d Examine the lists 2onTimer Recording with the VCR Plus+ Programming System FF /OK button Press the EXIT/STATUS button. Program WAS COMQuick Programming Channels are programmed. Details are on pagesHrs Cassette type / Playback TimeTape Speeds Will play tapes recorded in LP, but LP will notSame length of time every week If you forget to turn off the VCRSage, press the Clear button Checking, Editing, or Clearing Timer Recordings Quick Programming cont’dTimer Recording Speed Setting Follow the steps below to set Timer REC Speed to AutoRerecording Tape Duplication VCR 1 will play your tape. Insert a prerecorded tape in VCRAudio and video cables are not included Index Search These features are not available with the VRA451 Receiving a Stereo BroadcastReceiving a Second Audio Program Multi-Channel Television Sound System VRA651 only cont’d Press the RECord/OTR button to start recordingHi-Fi Stereo Tape Playback VRA651 only Video Stabilizer Choose to soften the picture Natural This is generally the preferred settingSmartPicture Choose to emphasize the edge PictureViewing a Still Picture Playback OptionsForward and Reverse Searching Viewing a Slow Motion PictureWhen Child Lock is activated Dash will appear on the display panelBlue Background Automatic Operation Features Glossary Cable Box/DBS Output Channel channel 03 orSpecifications Helpful Hints Helpful Hints cont’d Limited Warranty Model # Serial #Controls Quick programming 36-39 Deleting Operation indicatorsReviewing 34-35Page Page Supplied Accessories
Top Page Image Contents