CBC CTR-030NC-2 manual Power Cord, Audio IN/OUT Jack, Video IN/OUT Jack Reset Button

Page 7

CONTROL NAMES AND LOCATIONS (cont’d)

REAR

1				2	3
1	ALARM IN				VIDEO IN
2	ALARM OUT			AUDIO IN
3	ALARM RESET			AUDIO IN
4	GND
5	SERIES IN
6	SERIES OUT
7	WARNING OUT
8	TRIGGER OUT
9	GND
10	LOW TAPE OUT	1 2 3 4	5 6 7 8 9 10 11 12	AUDIO OUT
11	1 SHOT REC IN
12	GND
	RESET
					VIDEO OUT
	4		5

PREPARATION

1.POWER CORD

Connect only to an AC 100-240V, 50/60Hz outlet.

2.AUDIO IN/OUT JACK

Connect the audio input and output terminal.

3.VIDEO IN/OUT JACK

4.RESET BUTTON

Use this button to reset the VCR.

5.12-PIN TERMINAL BLOCK Connect external signals.

Connect the video input and output terminal.

Terminal Signal Levels

TERMINAL				SIGNAL LEVEL			IN/OUT

1. ALARM IN		VIH		VIL		VIH: 4~5V, VIL: 0~0.6V	INPUT
			T	VIL		T: above 250msec
			T			T: above 250msec
2. ALARM OUT		VOH		VOL		VOH: 4~5V, VOL: 0~0.6V	OUTPUT
2. ALARM OUT		VOH		VOL		VOH: 4~5V, VOL: 0~0.6V	OUTPUT
			T			T: ALARM REC STATE
3. ALARM RESET							INPUT
3. ALARM RESET		VIH		VIL		VIH: 4~5V, VIL: 0~0.6V	INPUT
			T	VIL		T: above 250msec
			T			T: above 250msec
5. SERIES IN						VIH: 4~5V, VIL: 0~0.6V	INPUT
5. SERIES IN		VIH		VIL		VIH: 4~5V, VIL: 0~0.6V	INPUT
			T	VIL		T: above 250msec
			T			T: above 250msec
6. SERIES OUT							OUTPUT
6. SERIES OUT		VOH		VOL		VOH: 4~5V, VOL: 0~0.6V	OUTPUT
			T	VOL		T: above 250msec
			T			T: above 250msec
7. WARNING OUT							OUTPUT
7. WARNING OUT		VOH		VOL		VOH: 4~5V, VOL: 0~0.6V	OUTPUT
			T	VOL		T: until any key is pressed
			T			T: until any key is pressed
8. TRIGGER OUT							OUTPUT
8. TRIGGER OUT		VOH		VOL		VOH: 4~5V, VOL: 0~0.6V	OUTPUT
			T	VOL		T: above 8~10msec
			T			T: above 8~10msec
10. LOW TAPE OUT							OUTPUT
10. LOW TAPE OUT		VOH		VOL		VOH: 4~5V, VOL: 0~0.6V	OUTPUT
			T	VOL		T: below 5 min, end of tape
			T			T: below 5 min, end of tape

11. 1-SHOT REC IN		VIH		VIL		VIH: 4~5V, VIL: 0~0.6V	INPUT
			T	VIL		T: above 250msec
			T			T: above 250msec
4, 9, 12. GND			–			0V	COMMON
			–			0V

5

Image 7

Contents Time Lapse VCR Page Important Safety Instructions Introduction Moisture CondensationContents FeaturesControl Names and Locations Audio IN/OUT Jack Power CordVideo IN/OUT Jack Reset Button PIN Terminal Block Connect external signalsLock Repeat CLOCK, Tape COUNTER, ErrorCassette Indication VCR Function Indication Installation Multiplexer Connections HOW to Connect Multiplexer with Trigger Input TerminalHOW to Connect Switcher Without Trigger Input Terminal Matrix Switcher ConnectionsSeries Record Connection Alarm Record ConnectionMenu Selection Setting the on Screen DisplayMain Menu Setting the Setup Menu Example May 23, 2003 Setting the SET TimeVCR SET UP Menu Clock SET UP MenuLoading Safety TABWhen Handling Video Cassettes Video Cassette TapesTracking Control Press REC/PLAY Hours time modeNormal Playback Normal PlaybackTo Watch a Field Advance Picture To Search Alarm RecordingSpecial Effects Playback To Watch a Still PictureJog Dial During Still modeShuttle Ring JOG DialTape Remaining Tape Counter Memory FeatureReal Time Counter Counter Memory FunctionNormal Recording During the Recording modeRepeat Recording REC Mode MenuTimer REC Mode Menu Timer RecordingDAY option Series Recording Alarm SET UP Alarm RecordingFor example When the Alarm REC Mode is set to L6H Alarm Recording cont’dAlarm REC Mode Menu Check the Alarm Record InformationRecording Time Table Information USE to Lock ON/OFF Switch Check the Power Fail RecallPower Fail Inform Menu SELF-DIAGNOSIS Error Code TableVideo Head Cleaning Service Guide TableSymptom Check Point & Correction TroubleshootingGeneral Specifications3834RS0069H