Setup, Connections, Hint | Sylvania DVC841G instruction

Setup

Connections

Please refer to “Basic TV Connection” on the front page before you use this unit.

RF Output Channel

If channel 3 has been already occupied for broadcasting,

1)Set your TV to channel 4.

2)Insert a pre-recorded tape into this unit. ) Press [OUTPUT] on the unit so that the

VCR OUTPUT light is lit.

•If noise appears on the TV screen, press [VCR/TV] on the remote control.

4) Press [PLAY B] once.

5)After a few seconds, press and hold [PLAY B] on the unit for seconds.

•The RF output channel will change to channel 4 from channel and you will see a playback picture.

•When a picture does not appear on the TV screen, repeat step 4.

6)Press [STOP C] to stop playback.

•The RF output channel does not change when you adjust tracking during playback. In case RF output channel changes you can easily switch it back just start the playback again then press and hold [PLAY B] on the unit for seconds.

Setup

Hint for Cable Box or Satellite Box

	(Cable box or			(Back of DVD/VCR)
	(Cable box or
		Satellite box)	ANT-IN
Satellite or	IN	OUT		RF cable
Cable TV			ANT-OUT	RF cable
signal				(supplied)
				(Back of TV)

Select this connection when you want to view or record a scrambled channel. With this connection, channels cannot be changed on the unit. You can view or record ONLY

the channels you have selected on the cable box or the satellite box.

•While you are recording, only the recorded channel can be viewed.

To select channels of the cable box or satellite box

1)Turn on the unit by pressing [POWER], then press [VCR/TV]. The POWER indicator on the front panel will light, then press [SKIP/CH. G/K, H/L] to select channel or 4 (the same channel as the output channel of the cable box or satellite box).

•If you use the channel 4, you need to change the unit’s RF output to channel 4. Refer to “RF Output Channel”.

2)At the TV, select channel or 4 (the same channel as you have selected at step 1).

) On the cable box or satellite box, select the channel you want to view or record.

Connection to an Audio System

	Method 1		Method 2
Audio	Stereo system		Dolby Digital decoder,
	Stereo system		MD deck or DAT deck
		Analog audio	MD deck or DAT deck
	L R	Analog audio	COAXIAL	Digital audio
	L R
		input jacks		input jack
	Audio cable		Audio Coaxial
	Audio cable		Digital cable
	(supplied)		(commercially
			available)

	DVD/VCR	VCR
	AUDIO OUT
AUDIO OUT	L
AUDIO OUT

DIGITAL	DVD	S-VIDEOVIDEO OUT
DIGITAL	AUDIO	S-VIDEOVIDEO OUT
		COMPONENT
AUDIO OUT	OUT	OUT

(Analog)	R

DVD/VCRor

DIGITAL	DVD	S-VIDEOVIDEO OUT
DIGITAL	AUDIO	S-VIDEOVIDEO OUT
		COMPONENT
AUDIO OUT	OUT	OUT

(DVD mode only)

DIGITAL COAXIAL

AUDIO OUT

Setting

Connection

Connecting to a Dolby Digital decoder for Dolby Digital audio output.

Connecting to the other equipment (an MD deck or DAT deck etc.) without Dolby Digital decoder.

SETUP > QUICK> DOLBY DIGITAL

BITSTREAM

PCM

•Playing a DVD using incorrect settings may generate noise distortion and may also damage the speaker.

* To complete these settings, refer to pages 20-21.

Hint

•The audio source on a disc in a Dolby Digital Multi channel surround format cannot be recorded as digital sound by an MD or DAT deck.

•By hooking this unit up to a Multi channel Dolby Digital decoder, you can enjoy high-quality Dolby Digital Multi channel surround sound as heard in the movie theaters.

•Playing a DVD using incorrect settings may generate noise distortion and may also damage the speakers.

– 6 –

DVC841G_E8A04UD.indd 6

2006/02/08 18:5:49