Sylvania DVC865G owner manual Quick Use Guide, Connections, Clock Set Up, RF Output Channel

Quick Use Guide

1	Connections	3 Press [B] to start Auto Set Up.	CH 01
Please refer to “Basic TV Connection” on the front page			AUTO SET UP
before you use this unit.

✄

RF Output Channel

If channel 3 has been already occupied for broadcasting,

1)Set your TV to channel 4.

2)Insert a pre-recorded tape into this unit.

3)Press [OUTPUT] on the unit so that the VCR OUTPUT light is lit.

•If noise appears on the TV screen, press [VCR/TV] on the remote control.

4)Press [PLAY B] once.

5)After a few seconds, press and hold [PLAY B] on the unit for 3 seconds.

•The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.

•When a picture does not appear on the TV screen, repeat step 4.

6)Press [STOP C] to stop playback.

2 Installing the Batteries for the Remote Control

1 2 3

3	VCR/DVD Switching
			POWER			OPEN/CLOSE
				SPEED	AUDIO	/EJECT
			1	2	3
						SKIP/CH.
			4	5	6
						VCR/TV
			7	8	9
						SLOW
		VCR button		0	+10
			DISPLAY	VCR	DVD	PAUSE
		DVD button
				PLAY
				STOP
		OUTPUT	REC/OTR
			MENU		ENTER
	VCR	DVD	SETUP	TOP MENU		RETURN
		DVD OUTPUT	MODE	ZOOM	MODE	C. RESET
					SEARCH	CLEAR/
		light	T-SET	ANGLE	REPEAT	A-B
			SUBTITLE

OUTPUT button

VCR OUTPUT light

VCR MODE

Press [VCR] on the remote control.(Verify that the VCR OUTPUT light is lit.)

DVD MODE

Press [DVD] on the remote control.(Verify that the DVD OUTPUT light is lit.)

Hint

•Pressing only [OUTPUT] on the front panel DOES NOT switch the mode of the remote control. You MUST select the correct mode on the remote control.

Do you connect the cable from the cable box or the satellite box to the unit’s ANT-IN jack?

YES NO

Yes Press [MENU] to exit.

No Please wait for a few minutes.

After scanning...

•The tuner stops on the lowest memorized channel.

•You can select only the channels memorized in this unit by using [SKIP/CH. G/K, H/L] (or [CHANNEL K/L]).

•If “AUTO SET UP” appears on the TV screen again, check the cable connections. Then, press [B] once again.

5	Clock Set Up
	VCR
1	Press [MENU] and select “CLOCK SET“.	- M E N U -
	Then press [B] to go to next step.	TIMER PROGRAMMING
		AUTO REPEAT	[OFF]
	MENU	CHANNEL SET UP
		B CLOCK SET
		LANGUAGE SELECT
	or	AUDIO OUT
		TV STEREO	[ON]

SAP

•If the clock is not set, the CLOCK SET screen appears when you press [MENU]. In this case, go to step 2.

2	Select the current month.	MONTH DAY			YEAR
			CLOCK SET
	Then press [B] to go to next step.	1 0	/	– –	– – – –
		HOUR MINUTE			AM/PM
	or	– –	:	– –	– –
3	Select the current day.		CLOCK SET
	Then press [B] to go to next step.	MONTH DAY			YEAR
		1 0	/	0 2	– – – –
		HOUR MINUTE			AM/PM
	or	– –	:	– –	– –
4	Select the current year.	MONTH DAY			YEAR
			CLOCK SET
	Then press [B] to go to next step.	1 0	/	0 2	2 0 0 6
		HOUR MINUTE			AM/PM
	or	– –	:	– –	– –
5	Select the current hour.		CLOCK SET
	Then press [B] to go to next step.	MONTH DAY			YEAR
		1 0	/	0 2 MON 2 0 0 6
		HOUR MINUTE			AM/PM
	or	0 5	:	– –	– –
6	Select the current minute.	MONTH DAY			YEAR
			CLOCK SET
	Then press [B] to go to next step.	1 0	/	0 2 MON 2 0 0 6
		HOUR MINUTE			AM/PM
	or	0 5	:	4 0	– –

4	Turn On the Unit for the First Time
	VCR
1	Turn on the TV and set it to channel 3.

•If channel 3 has been already occupied for broadcasting, see “RF Output Channel” section.

2 Select your language in the first time you turn on this unit.
Then press [B] to go to next step.	LANGUAGE SELECT
POWER	B ENGLISH	[ON]

FRANCAIS

ESPAÑOL

or

7	Select “AM” or “PM”.		CLOCK SET
		MONTH DAY		YEAR
		1 0	/ 0 2 MON 2 0 0 6
	or	HOUR MINUTE		AM/PM
		0 5	: 4 0	P M AM
				B PM
8	To exit the CLOCK SET screen

– 27 – EN

E8A00UD_E8C00UD.indd 27 2006/08/18 13:11:41