Sylvania DVC860E owner manual Preset for Use, Turn on the unit for the first time, Clock Set Up

Page 10

Preset for Use

Turn on the unit for the first time

VCR

VCR

1

Turn on the TV and set it to channel 3.

If channel 3 is already occupied for broadcasting, see“RF Output Channel” section.

To Preset the Channel Again

1)Press the MENU button until the main menu appears.

2)Select "CHANNEL SET UP" by pressing the K or L button. Then, press the B but- ton.

3)Select "AUTO SET UP" by pressing the

K or L button. Then, press the B button. After scanning, the tuner stops on the low- est memorized channel.

4

 

CLOCK SET

 

MONTH DAY

YEAR

or

0 3

/ 1 5 MON 2 0 0 4

 

 

 

 

HOUR MINUTE

AM/PM

 

– –

: – –

– –

 

Select the current year

2

POWER

Remote Control

TV Screen

 

 

 

LANGUAGE SELECT

 

 

B ENGLISH

[ON]

 

or

FRANCAIS

 

 

 

 

 

Setup

 

ESPAÑOL

 

 

 

 

 

3

 

 

 

CH 01

AUTO SET UP

Do you connect the cable from the cable box or the satellite box to the DVD/VCR’s ANT IN jack?

YES

Yes Press the MENU button to exit

Refer to “Hint for Cable Box or Satellite Box” section on

page 6.

NO

No Please wait for a few minutes.

After scanning...

The tuner stops on the lowest memorized channel.

You can select only the channels memo- rized in this unit by using the CHANNEL buttons.

If "AUTO SET UP" appears on the TV screen again, check the cable connections. Then, press the B button once again.

Hint

Repeat these steps only if either there was a power failure or this unit has been unplugged for more than 30 seconds.

To Change the On-Screen Language

1)Press the MENU button until the main menu appears.

2)Select "LANGUAGE SELECT" by press- ing the K or L button. Then, press the B button.

3)Select "ENGLISH" , "FRANCAIS" or "ESPAÑOL" by pressing the K or L but- ton. Then, press the CLEAR/C.RESET button.

Hint

If you accidentally select Spanish or French and need English: Press the MENU button and choose SELEC.

IDIOMA, or SELECTION LANGUE. Press the B button, and select ENGLISH. Finally, press the CLEAR/C.RESET button.

Clock Set Up

 

VCR

VCR

 

1 MENU

-MENU-

TIMER PROGRAMMING

AUTO REPEAT [OFF]

CHANNEL SET UP

BCLOCK SET LANGUAGE SELECT AUDIO OUT

 

TV STEREO [ON]

 

SAP

or

• If the clock is not set, the

 

CLOCK SET screen

 

appears when you press

 

the MENU button. In this

 

case, go to step [2].

2

 

CLOCK SET

or

MONTH DAY

YEAR

0 3

/ – –

– – – –

 

HOUR MINUTE

AM/PM

 

– –

: – –

– –

 

Select the current month

5

CLOCK SET

MONTH DAY

YEAR

0 3

/ 1 5 MON 2 0 0 4

or

 

 

HOUR MINUTE

AM/PM

0 5

: – –

– –

Select the current hour

6

CLOCK SET

MONTH DAY

YEAR

0 3

/ 1 5 MON 2 0 0 4

or

 

 

HOUR MINUTE

AM/PM

0 5

: 4 0

– –

Select the current minute

7

CLOCK SET

MONTH DAY

YEAR

0 3

/ 1 5 MON 2 0 0 4

or

 

 

HOUR MINUTE

AM/PM

0 5

: 4 0

P M AM

 

 

B PM

Select “AM” or “PM”

8To exit the CLOCK SET screen.

Hint

• To go back one step, press the s button

(during the steps [2] to [7].)

• Your clock setting will be lost if either there

is a power failure or this unit has been

To Select a Channel

You can select a channel by directly entering channel using the Number but- tons on the remote control.

Notes for using the Number buttons:

When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number.(For example: 117, press 1,1,7)

You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on).

3

 

CLOCK SET

 

MONTH DAY

YEAR

or

0 3

/ 1 5

– – – –

 

 

 

 

HOUR MINUTE

AM/PM

 

– –

: – –

– –

 

Select the current day

unplugged for more than 30 seconds.

– 10 –

EN

Image 10
Contents Table of Contents Supplied AccessoryBasic TV Connection Make your contribution to the environment PrecautionsLaser Safety Serial NoImportant Safeguards About Copyright Installation LocationMoisture Condensation Warning Avoid the Hazards of Electrical Shock and FirePlayable Discs Setup About the DiscsConnections Unplayable DiscsHint for Cable Box or Satellite Box Connection to an Audio SystemMethod Connection to a TV for VideoFront & Rear Terminals If your TV is compatible with progressive scanning 480pInstalling the Batteries for the Remote Control About the Remote Control and Front PanelRemote Controls Install two AA batteriesVCR/DVD Switching Front Panel DisplayClock Set Up Preset for UseTurn on the unit for the first time Recording & OTR One Touch Recording VCR Function PlaybackOther Operations To Check, Correct, or Cancel a Timer Program Recording FeaturesTimer Recording On-Screen OperationsMTS System Multi-Channel Television Sound Hint for Timer RecordingWhen You Play Back a Tape Recorded in Hi-Fi Stereo Copying a Video TapeIndex Search Special FeaturesTime Search Auto RepeatDVD Function Playback On-Screen Display MP3 PlaybackMP3 Playback Track Search Marker SetupSearch Function Title / Chapter SearchRepeat A-B Playback Repeat / Random / Programmed PlaybackRepeat Playback Random PlaybackSpecial Settings Language Setting DVD Set Up20 a 21 B 21 C See Hint to the right Display SettingAudio Setting Minutes of no useDVD Functions Parental SettingIf you have set a password already Parental menuTroubleshooting Guide Specifications MaintenanceLanguage List For Spanish For Spanish For Spanish 0VMN04012 / H9600UD TelVan Ness Avenue, Torrance, CA Head Office 100 North Street, Teterboro, NJ