Intel 8080, 8085 manual ISIS-II Error Messages

Page 31

80801808S Assembler

Error Messages

Assembler Control Enor

lIesuge

COMMAND ERROR

explanation

Assembler console command line syntax is illegal, usually due to missing or illegal delimiter or missing parameter. The entire command line is ignored.

ISIS-II Error Messages

By convention, error numbers 1-99 are reserved for errors that originate in or are detected by the resident routines of ISIS; error numbers 101-199 are reserv- ed for user programs; numbers 200-255 are used for errors encountered by nonresident system routines. In the following list an asterisk precedes fatal er- rors. The other errors are generally nonfatal unless they are issued by the CONSOLE system call.

o No error detected.

*1 Insufficient space in buffer area for a required buffer.

2AFIN does not specify an open file.

3Attempt to open more than six files simultaneously.

4megal filename specification.

Smegal or unrecognized device specification in filename.

6 Attempt to write to a fde open for input.

*7 Operation aborted; insufficient diskette space.

8Attempt to read from a file open for output.

9No more room in diskette directory.

10Filenames do not specify the same diskette.

11 Cannot rename file; name already in use.

12Attempt to open a fde already open.

13No such file.

14Attempt to open for writing (output or update) or to delete or rename a write-protected file.

*15 Attempt to load into ISIS area or buffer area. *16 Incorrect ISIS binary format.

17Attempt to rename or ddete a file not on diskette.

18Unrecognized system call.

19Attempt to seek in a file not on diskette.

20Attempt to seek backward past beginning of file.

21Attempt to rescan a file not line edited.

22Illegal ACCESS parameter to OPEN or access mode impossible for file specified (input mode for :LP:, for example).

23No filename specified for a diskette file.

24Input!output error on diskette (see below).

2S Incorrect specification of echo file to OPEN.

26Incorrect SWID parameter in ATIRIB system call.

27Incorrect MODE parameter in SEEK system call.

28Null file extension.

*29 End of file on console input. *30 Drive not ready.

31Attempted seek on file open for output.

32Can't delete an open file.

33megal system call parameter.

34Bad RETSW parameter to LOAD.

3S Attempt to extend a file opened for input by seeking past end-of-file.

7-3

Image 31
Contents ISIS-II 8080/8085 Macro Assembler Operatorsmanual Scope Prefacei Page Contentsi Page ISIS-II Assembler Environment Chapter Assembler OverviewInput/Output Files Assembler Files Symbol-Cross-Reference FilePage Chapter ISIS·IIAssembler Controls Primary Controls General Controls ISIS-II Assembler Control Lines Page Activation Sequence Sample AssemblyAsmbo MBADD.SRC Symbols Xref Macrofile Reducing Assembly Time Page Chapter List File Formats List File Formats 808O/808S Assembler Assembly Output Line Symbol Table Listing Cross-Reference Output Line Symbol-Cross-Reference ListingChapter PL/M Linkage Conventions Page Relocatable Programs Absolute ProgramsPage Error Codes Error Detection and ReportingError Messqes ISIS-II Error Messages FOCC= OOnn Request for Readerscomments 111111
Related manuals
Manual 96 pages 34.66 Kb Manual 262 pages 56.67 Kb Manual 160 pages 43.4 Kb

8080, 8085 specifications

The Intel 8085 and 8080 microprocessors were groundbreaking innovations in the world of computing, paving the way for future microprocessor development and personal computing.

The Intel 8080, introduced in 1974, was an 8-bit microprocessor that played a fundamental role in the early days of personal computing. With a 16-bit address bus, it had the capability to address 64 KB of memory. Running at clock speeds of 2 MHz, the 8080 was notable for its instruction set, which included 78 instructions and 246 opcodes. It supported a range of addressing modes including direct, indirect, and register addressing. The 8080 was compatible with a variety of peripherals and played a crucial role in the development of many early computers.

The microprocessor's architecture was based on a simple and efficient design, making it accessible for hobbyists and engineers alike. It included an 8-bit accumulator, which allowed for data manipulation and storage during processing. Additionally, the 8080 featured registers like the program counter and stack pointer, which facilitated program flow control and data management. Its ability to handle interrupts also made it suitable for multitasking applications.

The Intel 8085, introduced in 1976, was an enhancement of the 8080 microprocessor. It maintained a similar architecture but included several key improvements. Notably, the 8085 had a built-in clock oscillator, simplifying system design by eliminating the need for external clock circuitry. It also featured a 5-bit control signal for status line management, which allowed for more flexible interfacing with peripheral devices. The 8085 was capable of running at speeds of up to 3 MHz and had an extended instruction set with 74 instructions.

One of the standout features of the 8085 was its support for 5 extra instructions for stack manipulation and I/O operations, which optimized the programming process. Additionally, it supported serial communication, making it suitable for interfacing with external devices. Its 16-bit address bus retained the 64 KB memory addressing capability of its predecessor.

Both the 8080 and 8085 microprocessors laid the groundwork for more advanced microprocessors in the years that followed. They demonstrated the potential of integrated circuits in computing and influenced the design and architecture of subsequent Intel microprocessors. Their legacy endures in the way they revolutionized computing, making technology accessible to a broader audience, and their influence is still felt in the design and architecture of modern microprocessors today.