Logitech 1100 user manual Installing the RF Wireless Extender, Using the Emitters

Page 38

38

Installing the RF Wireless Extender

You have a lot of ﬂexibility where you can install the RF Wireless Extender. You can mount it on a wall or you can install it inside the cabinet where your devices are located.

Before you install the RF Wireless Extender, you should decide what you are doing with the emitters. If you are attaching emitters to the devices, then the RF Wireless Extender has to be within connecting distance to the devices. If you are not connecting the emitters to the devices, then all of the components of your system must be within 5 metres and have a direct line of sight with the RF Wireless Extender.

Logitech recommends that you make sure all of your devices are working properly before installing the RF Wireless Extender.

Using the Emitters

The RF Wireless Extender has four dual-head IR (infrared) emitters that can control up to eight devices. Each emitter can control two devices.

There are 3 possible ways the RF Wireless Extender can send IR signals to the devices of your entertainment system:

1.The RF Wireless Extender sends IR signals in all directions. In this case, no emitters are attached to the components or plugged into the RF Wireless Extender. For this method to work, all of the system components must be within 5 meters and have a direct line of sight with the RF Wireless Extender.

2.An emitter is attached to each of the components and each emitter is randomly plugged into the RF Wireless Extender ports. No ports are assigned for individual components, so it doesn’t matter which emitter is plugged into A, B, C, or D port on the RF Wireless Extender.

3.An emitter is attached to each of the components, individual ports are assigned to each of the components, and the emitters are plugged into speciﬁc ports of the Wireless Extender.

Finding where to place the emitters

To ﬁnd where to place the emitters:

1.Take the remote you use to turn the device on or off, move toward the device and press the power button on and off as you get closer to the device.

2.If the device stops responding, stop moving forward, move the remote slightly up/down/left/right until the device responds again.

3.Repeat Step 1 and 2 until the remote is touching the device.

Image 38

Contents Version Contents Figuring out which inputs your system uses Page Introduction Buttons on your Harmony Navigation icons Activities Commands common to your ActivityFavorite Channels DevicesAB C Status iconsTurning off your devices Switching between ActivitiesSelecting an Activity Using the Help button Controlling your devices individually Charging your remoteGathering your device information Setting up your Harmony 1100 for the ﬁrst timeOverview of the setup process Locating manufacturer and model number on your devicesConnecting your Harmony 1100 to your computer Click Create New AccountAdding new devices at a later time Setting up the devices you want to controlSetting up Activities for your Harmony Updating the remote Testing your setup -- Switching between Activities Testing your setupTesting your setup -- Starting an Activity Renaming an Activity Changing your setupAdding and changing your Activities Adding and changing your devicesAdding an extra device passthrough to an Activity Controlling the Remote Assistant Select the Remote Settings tab Click Display SettingsCustomizing the on-remote help Smart HelpPage Select Set up Favorite Channels Click Re-order ActivitiesFavorite channel icons Click Customize ButtonsClick the Remote Settings tab Click Set Up a Slideshow Naming buttons that appear on the remote’s screenSelect Remote Settings Select Backlight Changing the backlight settingsSetting a background Select the Remote Settings tab Select Set a backgroundNaming conventions Adding additional features to your HarmonyNaming a new command your remote learned Inter-Key Delay Types of delays or speed settingsPower On Delay Input DelaySelect Adjust the delays speed settings Adjusting the delay between IR commands speed settingsInter-Device Delay RepeatsTesting your remote settings after a remote upgrade Maintaining your HarmonyTroubleshooting problems with your Harmony TV doesn’t go to the right input when starting ActivitiesPage Option 1 One source button Option 2 Several source buttonsOption 4 Select the source from a list Turn on all your devicesOption 3 Select the input from an on-screen menu Watch the TV Listen to the soundRF Wireless Extender Lights on the RF Wireless ExtenderSetting up the RF Wireless Extender Click the Remote Settings tab Click Manage RemotesControlling a device with the RF Wireless Extender Controlling a device with the Harmony remoteFinding where to place the emitters Installing the RF Wireless ExtenderUsing the Emitters Attaching the emitters Click Remote Settings Click Manage Remotes Adding additional RF Wireless ExtendersRemoving the RF Wireless Extender from your network Contacting Customer Support Getting help with your online setupGetting help with your Harmony remote Finding answers to questionsUsing the On-Remote Help Logitech’s Harmony Remote user forumsAppendix a Device Information Appendix B Glossary Receiver Passthrough Personal Video Recorder PVRPre-ampliﬁer Pre-amp Sound Processing Stereo receiver Tuner Power strip Appendix C Product Speciﬁcation

Related manuals

Manual 48 pages 28.38 Kb

Manual 48 pages 62.86 Kb